Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17C3  Rear Differential Lock Limit SW Circuit  


DESCRIPTION

When the differential lock shift actuator is switching between free and lock, the RLY1 and RLY2 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
FREE Switching LOCK
RLY1 ON ON OFF
RLY2 OFF ON ON

A malfunction is detected depending on the combination of the 2 circuits that make up the limit switch of the differential lock shift actuator assembly.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17C3
1.

When rear differential is switching between free and lock (differential lock shift motor operating) with ignition switch turned to ON

2.

The combination of RLY1 and RLY2 does not match

3.

0 seconds

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Differential lock shift actuator



WIRING DIAGRAM

C341716E01
5.073,3.081 5.488,3.311 0.415,0.230 10 A27 5.054,3.333 6.867,3.498 1.813,0.165 10 4 Wheel Drive Control ECU 5.044,0.789 5.409,0.970 0.364,0.181 10 RLY1 5.044,1.517 5.409,1.698 0.364,0.181 10 RLY2 4.75,1.501 4.978,1.674 0.228,0.173 10 2 4.722,0.758 4.950,0.932 0.228,0.173 10 11 3.723,0.749 3.951,0.922 0.228,0.173 10 6 3.704,1.501 3.932,1.674 0.228,0.173 10 5 0.828,1.501 1.055,1.674 0.228,0.173 10 4 1.869,2.035 2.747,2.237 0.878,0.202 10 Limit Switch 1.309,2.778 1.650,2.952 0.341,0.174 10 f1 1.306,2.967 3.214,3.199 1.908,0.232 10 Differential Lock Shift Actuator 5.456,0.27 5.750,0.527 0.295,0.258 10 IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK SHIFT ACTUATOR)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

Disconnect the f1 differential lock shift actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-11 (RLY1) - f1-6 Always Below 1 Ω
A27-2 (RLY2) - f1-5 Always Below 1 Ω
f1-4 - Body ground Always Below 1 Ω
A27-11 (RLY1) or f1-6 - Body ground Always 10 kΩ or higher
A27-2 (RLY2) or f1-5 - Body ground Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.

Disconnect the f1 differential lock shift actuator connector.


b.
U165697E02
1.656,0.25 1.906,0.438 0.25,0.188 10 false f1 0.135,0.031 0.375,0.271 0.24,0.24 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
f1-6 - Body ground Ignition switch ON 10 to 14 V
f1-5 - Body ground Ignition switch ON 10 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Differential Lock Shift Actuator)

Result:
Result Proceed to
OK A
NG for LHD B
for RHD C




A

B

C