Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION J

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies the power source to the suspension control ECU.

WIRING DIAGRAM

C177465E03
5.438,3.854 7.052,4.083 1.615,0.229 10 false Suspension Control ECU 6.208,2.635 6.667,2.844 0.458,0.208 10 false GND 6.188,3.188 6.646,3.396 0.458,0.208 10 false GND 5.823,2.646 6.094,2.792 0.271,0.146 10 false K34 5.813,3.188 6.104,3.333 0.292,0.146 10 false K35 6.177,1.219 6.365,1.406 0.188,0.188 10 false IG 5.813,1.229 6.083,1.385 0.271,0.156 10 false K34 5.906,1 6.01,1.167 0.104,0.167 10 false 5 5.896,2.427 6,2.573 0.104,0.146 10 false 1 5.885,2.99 6,3.156 0.115,0.167 10 false 6 4.667,1.229 4.875,1.406 0.208,0.177 10 false 3C 4.708,1.01 4.833,1.167 0.125,0.156 10 false 5 3.5,1.375 4.427,1.583 0.927,0.208 10 false ECU-IG No. 4 2.229,2.344 3.823,2.542 1.594,0.198 10 false IG No. 4 (Built-in Relay) 1.833,1.229 2.104,1.406 0.271,0.177 10 false 3A 1.885,1.021 1.979,1.156 0.094,0.135 10 false 1 1.823,1.792 2.042,1.948 0.219,0.156 10 false 3C 1.844,1.604 2.052,1.75 0.208,0.146 10 false 22 1.833,3.115 2.042,3.26 0.208,0.146 10 false 3C 1.875,2.906 1.99,3.052 0.115,0.146 10 false 8 0.125,1.813 1.479,2.021 1.354,0.208 10 false from Main Body ECU 0.688,1.219 1.5,1.427 0.813,0.208 10 false from Battery 2.385,3.833 4.292,4.073 1.906,0.24 10 false Cowl Side Junction Block RH

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG POWER SOURCE VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and the tester on.


c.

Read the "IG Power Source Voltage" item in the Data List.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Source Voltage Power supply voltage /
min.: 0 V
max.: 255 V
Engine switch on (IG): 11 to 14 V -

OK:

11 to 14 V




OK

NG

2.INSPECT FUSE (ECU-IG NO. 4)
2.INSPECT FUSE (ECU-IG NO. 4)
a.

Remove the ECU-IG No. 4 fuse from the cowl side junction block RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 4 fuse Always Below 1 Ω




OK

3.INSPECT COWL SIDE JUNCTION BLOCK RH (IG NO. 4 RELAY)

NG

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU)
3.INSPECT COWL SIDE JUNCTION BLOCK RH (IG NO. 4 RELAY)
a.

Disconnect the K34 ECU connector.


b.
U164812E02
2.313,2.458 1.594,2.865 1.594,2.865 1.594,2.979 false 0.344,0.073 2.656,0.479 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 1.396,3 1.823,3.198 0.427,0.198 10 false 5 (IG) 1.646,2.115 1.906,2.26 0.26,0.146 10 false K34

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K34-5 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE SUSPENSION CONTROL ECU

NG

4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU AND BODY GROUND)
U164864E01
0.621,0.102 2.935,0.508 2.314,0.406 10 Rear view of wire harness connector: (to Suspension Control ECU) 4.187,0.098 6.593,0.624 2.406,0.526 10 Front view of wire harness connector: (to Cowl Side Junction Block RH) 1.003,1.701 1.276,1.892 0.273,0.191 10 K35 2.817,1.537 3.108,1.692 0.291,0.155 10 K34 1.953,2.479 2.345,2.649 0.392,0.170 10 5 (IG) 2.798,2.489 3.366,2.663 0.568,0.174 10 1 (GND) 2.631,1.98 3.069,2.344 3.069,2.344 3.069,2.465 false 2.317,1.975 2.141,2.338 2.141,2.338 2.141,2.442 false 0.8,2.476 1.340,2.646 0.540,0.170 10 6 (GND) 1.432,1.975 1.054,2.343 1.054,2.343 1.054,2.451 false 5.293,1.028 5.584,1.183 0.291,0.155 10 3C

a.

Disconnect the K34 and K35 ECU connectors.


b.

Disconnect the 3C cowl side junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-5 (IG) - 3C-5 Always Below 1 Ω
K34-1 (GND) - Body ground Always Below 1 Ω
K35-6 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - COWL SIDE JUNCTION BLOCK RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BATTERY - COWL SIDE JUNCTION BLOCK RH)
a.

Disconnect the 3A cowl side junction block RH connector.


b.
U165800E01
0.343,0 2.756,0.420 2.412,0.420 10 Front view of wire harness connector: (to Cowl Side Junction Block RH) 0.722,1.414 0.947,1.632 0.225,0.218 10 3A

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COWL SIDE JUNCTION BLOCK RH AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COWL SIDE JUNCTION BLOCK RH AND BODY GROUND)
a.

Disconnect the 3C cowl side junction block RH connector.


b.
U164865E01
0.265,0.25 2.726,0.595 2.461,0.346 10 Front view of wire harness connector: (to Cowl Side Junction Block RH) 1.643,1.474 1.921,1.685 0.278,0.211 10 3C

Measure the voltage and resistance according to the value(s) in the tables below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-22 - Body ground Engine switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
3C-8 - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - ECU)
a.

Disconnect the K34 ECU connector.


b.
U164812E02
2.313,2.458 1.594,2.865 1.594,2.865 1.594,2.979 false 0.344,0.073 2.656,0.479 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 1.396,3 1.823,3.198 0.427,0.198 10 false 5 (IG) 1.646,2.115 1.906,2.26 0.26,0.146 10 false K34

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-5 (IG) - Body ground Always 10 kΩ or higher


HINT:

If a fuse is blown, replace the fuse.




OK

REPLACE COWL SIDE JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR