Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1715  Front Acceleration Sensor RH Malfunction  C1716  Front Acceleration Sensor LH Malfunction  C1717  Rear Acceleration Sensor Malfunction  C1796  Front Acceleration Sensor RH Malfunction (Test Mode DTC)  C1797  Front Acceleration Sensor LH Malfunction (Test Mode DTC)  C1798  Rear Acceleration Sensor Malfunction (Test Mode DTC)  


DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the driver side instrument panel, and 3) the passenger side instrument panel. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in the signal of each sensor. When the sensor cannot detect +/-1.96 m/s2 for 1 second or more during test mode, DTCs C1796, C1797 and C1798 are stored.

DTC Code Detection Condition Trouble Area
C1715
C1796
When either of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front acceleration sensor RH is detected for 1 second.

·

When there is a front acceleration sensor RH power supply voltage malfunction.


·

Harness or connector

·

Front acceleration sensor RH

·

Suspension control ECU


C1716
C1797
When either of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front acceleration sensor LH is detected for 1 second.

·

When there is a front acceleration sensor LH power supply voltage malfunction.


·

Harness or connector

·

Front acceleration sensor LH

·

Suspension control ECU


C1717
C1798
When either of the following conditions is met:
·

With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the rear acceleration sensor is detected for 1 second.

·

When there is a rear acceleration sensor power supply voltage malfunction.


Suspension control ECU (Houses rear acceleration sensor)

WIRING DIAGRAM

C177316E01
0.326,1.491 0.690,1.671 0.364,0.180 10 K37 0.326,1.696 2.204,1.900 1.878,0.205 10 Front Acceleration Sensor LH 1.109,0.356 1.564,0.498 0.455,0.142 10 SGFL 1.123,0.804 1.487,1.015 0.364,0.211 10 SGG 1.123,1.279 1.515,1.475 0.392,0.196 10 SGB 1.725,0.205 1.924,0.404 0.198,0.198 10 1 1.725,0.694 1.930,0.898 0.205,0.205 10 2 1.725,1.144 1.951,1.369 0.225,0.225 10 3 1.091,2.235 1.547,2.378 0.455,0.142 10 SGFR 1.105,2.684 1.470,2.895 0.364,0.211 10 SGG 1.105,3.159 1.497,3.354 0.392,0.196 10 SGB 1.708,2.085 1.906,2.283 0.198,0.199 10 1 1.708,2.573 1.912,2.778 0.205,0.205 10 2 1.708,3.024 1.933,3.249 0.225,0.225 10 3 0.326,3.516 0.690,3.697 0.364,0.180 10 L35 0.326,3.721 2.204,3.926 1.878,0.205 10 Front Acceleration Sensor RH 5.7,0.208 6.009,0.426 0.309,0.218 10 22 5.68,0.703 6.045,0.955 0.364,0.253 10 13 5.676,1.161 5.984,1.360 0.308,0.198 10 23 6.105,0.36 6.560,0.502 0.455,0.142 10 SGFL 6.119,0.809 6.664,1.020 0.545,0.211 10 SGG2 6.119,1.264 6.678,1.460 0.559,0.196 10 SGB2 6.107,2.235 6.562,2.377 0.455,0.142 10 SGFR 6.121,2.683 6.689,2.894 0.568,0.211 10 SGG1 6.121,3.158 6.726,3.354 0.605,0.196 10 SGB1 5.705,2.102 5.906,2.277 0.201,0.175 10 24 5.687,2.56 5.908,2.748 0.221,0.188 10 14 5.685,3.025 5.924,3.202 0.239,0.176 10 15 5.293,3.571 5.607,3.751 0.313,0.180 10 K34 5.293,3.768 7.088,4.257 1.795,0.489 10 Suspension Control ECU (Houses Rear Acceleration Sensor)

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).

·

If DTCs C1717 and C1798 (Rear Acceleration Sensor Malfunction) are stored, replace the suspension control ECU (houses rear acceleration sensor).



PROCEDURE

1.CHECK ACCELERATION SENSOR (DATA LIST)
a.

Turn the engine switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and the tester on.


d.

Enter the following menus: Chassis / AHC / Data List.


e.

According to the display on the tester, read the Data List.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
(Up & Down)G Sensor FR G (up and down) front acceleration sensor RH reading/
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/-0.98 m/s2 at still condition Reading changes when vehicle (FR) is bounced
(Up & Down)G Sensor FL G (up and down) front acceleration sensor LH reading/
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/-0.98 m/s2 at still condition Reading changes when vehicle (FL) is bounced
(Up & Down)G Sensor Rear G (up and down) rear acceleration sensor reading/
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/-0.98 m/s2 at still condition Reading changes when vehicle (rear) is bounced

OK:

Reading changes when vehicle is bounced.




OK

2.RECONFIRM DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)
2.RECONFIRM DTC OUTPUT

b.

Perform a road test.


c.

Check for DTCs.

Result
Result Proceed to
DTC is output A
DTC is not output B



A

3.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)

B

3.CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)
NOTICE:

When inspecting the wire harnesses between the suspension control ECU and acceleration sensors, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect the connectors for the acceleration sensors (front RH, front LH), the fluid temperature sensor, and fluid pressure sensor on the ECU side.


a.

Check the front acceleration sensor RH side: (C1715)

U164782E01
0.433,0.126 2.841,0.489 2.408,0.363 10 Rear view of wire harness connector: (to Suspension Control ECU) 4.062,0.192 6.394,0.598 2.332,0.406 10 Front view of wire harness connector: (to Front Acceleration Sensor RH) 0.977,1.926 1.268,2.109 0.291,0.184 10 K35 2.211,1.923 2.511,2.107 0.300,0.184 10 K34 1.912,2.51 2.594,2.657 0.681,0.147 10 15 (SGB1) 2.847,2.51 3.556,2.659 0.710,0.149 10 24 (SGFR) 3.331,1.994 4.038,2.132 0.707,0.138 10 14 (SGG1) 2.686,2.063 2.231,2.378 2.231,2.378 2.231,2.455 false 2.686,2.119 3.212,2.378 3.212,2.378 3.212,2.476 false 2.731,2.059 3.289,2.059 false 4.518,1.377 4.818,1.560 0.300,0.184 10 L35 4.566,2.279 4.991,2.455 0.424,0.177 10 SGFR 5.982,2.279 6.316,2.468 0.335,0.189 10 SGB 5.264,2.372 5.622,2.547 0.357,0.174 10 SGG 5.164,1.697 4.771,2.091 4.771,2.091 4.771,2.232 false 5.395,1.73 5.395,2.316 false 5.594,1.709 6.117,2.073 6.117,2.073 6.117,2.241 false

i.

Disconnect the K34 and K35 ECU connectors.


ii.

Disconnect the L35 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-1 (SGFR) - K34-24 (SGFR) Always Below 1 Ω
L35-2 (SGG) - K34-14 (SGG1) Always Below 1 Ω
L35-3 (SGB) - K34-15 (SGB1) Always Below 1 Ω
K34-24 (SGFR) - Body ground Always 10 kΩ or higher
K34-14 (SGG1) - Body ground Always 10 kΩ or higher
K34-15 (SGB1) - Body ground Always 10 kΩ or higher




b.

Check the front acceleration sensor LH side: (C1716)

i.

Disconnect the K34 and K35 ECU connectors.


ii.

Disconnect the K37 sensor connector.

U164783E01
0.433,0.202 2.841,0.564 2.408,0.363 10 Rear view of wire harness connector: (to Suspension Control ECU) 4.062,0.192 6.394,0.598 2.332,0.406 10 Front view of wire harness connector: (to Front Acceleration Sensor LH) 0.979,1.927 1.281,2.111 0.302,0.184 10 K35 2.204,1.919 2.499,2.103 0.295,0.184 10 K34 1.912,2.51 2.594,2.657 0.681,0.147 10 23 (SGB2) 2.847,2.51 3.556,2.659 0.710,0.149 10 22 (SGFL) 3.331,1.994 4.038,2.132 0.707,0.138 10 13 (SGG2) 2.726,2.112 2.231,2.378 2.231,2.378 2.231,2.455 false 2.772,2.119 3.212,2.378 3.212,2.378 3.212,2.476 false 2.775,2.059 3.289,2.059 false 4.515,1.345 4.811,1.528 0.295,0.184 10 K37 4.429,2.367 4.848,2.565 0.420,0.198 10 SGFL 5.204,2.367 5.582,2.537 0.378,0.170 10 SGG 5.956,2.367 6.326,2.537 0.370,0.170 10 SGB 5.182,1.703 4.639,2.185 4.639,2.185 4.639,2.283 false 5.581,1.684 6.089,2.192 6.089,2.192 6.089,2.297 false 5.388,1.753 5.388,2.283 false


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K37-1 (SGFL) - K34-22 (SGFL) Always Below 1 Ω
K37-2 (SGG) - K34-13 (SGG2) Always Below 1 Ω
K37-3 (SGB) - K34-23 (SGB2) Always Below 1 Ω
K34-22 (SGFL) - Body ground Always 10 kΩ or higher
K34-13 (SGG2) - Body ground Always 10 kΩ or higher
K34-23 (SGB2) - Body ground Always 10 kΩ or higher





OK

4.INSPECT ACCELERATION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ACCELERATION SENSOR
C177935E06
2.844,1.5 3.104,0.885 3.104,0.885 3.156,0.885 true 2.594,1.604 2.448,2.25 2.448,2.25 2.448,2.375 true 1.448,1.885 1.583,1.885 1.583,1.885 2.406,1.604 true 5.875,0.208 6.406,0.406 0.531,0.198 10 false Upside 4.74,2.26 5.5,2.448 0.76,0.188 10 false Downside 1.135,1.802 1.448,2 0.313,0.198 10 false SGB 2.333,2.385 2.677,2.583 0.344,0.198 10 false SGG 3.208,0.792 4.479,0.969 1.271,0.177 10 false SGFR*1, SGFL*2 0.115,2.083 0.771,2.25 0.656,0.167 10 false *1: for RH 0.115,2.385 0.75,2.615 0.635,0.229 10 false *2: for LH 0.135,0.063 2.781,0.49 2.646,0.427 10 false Component without harness connected: (Acceleration Sensor)

a.

Turn the engine switch off.


b.

Remove the front acceleration sensor (See page Suspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>REMOVAL).

NOTICE:

Do not drop the acceleration sensor. If it is dropped, replace it with a new one.



c.

Connect 3 1.5 V dry cell batteries in series.


d.

Connect the positive (+) end of the batteries to terminal 3 (SGB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGG). Then measure the voltage between terminal 1 (SGFR*1, SGFL*2) and terminal 2 (SGG).

HINT:

*1: for RH

*2: for LH


NOTICE:

Do not apply a voltage of more than 6 V.


HINT:

The voltage may differ according to the amount that the sensor is tilted.


Standard Voltage:
for RH
Tester Connection Condition Specified Condition
1 (SGFR) - 2 (SGG) Sensor stationary Approx. 2.0 to 2.5 V
Sensor is tilted Change between approx. 0.9 to 2.3 V

for LH
Tester Connection Condition Specified Condition
1 (SGFL) - 2 (SGG) Sensor stationary Approx. 2.0 to 2.5 V
Sensor is tilted Change between approx. 0.9 to 2.3 V




OK

REPLACE SUSPENSION CONTROL ECU

NG