Home › Suspension › SUSPENSION CONTROL › ACTIVE HEIGHT CONTROL SUSPENSION › 2014.08–2015.08
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255367 ACTIVE HEIGHT CONTROL SUSPENSION C

SUSPENSION CONTROL  ACTIVE HEIGHT CONTROL SUSPENSION  C1719  Oil Temperature Sensor Circuit Malfunction  


DESCRIPTION

This circuit is used for sending the data to detect the fluid temperature of the pump. The abnormality of the fluid is judged by the ECU.

DTC Code Detection Condition Trouble Area
C1719 When one of the following conditions is met:
·

When detecting an abnormal signal from the fluid temperature sensor (fluid temperature sensor terminal voltage of ECU is 0.1 V or less or 4.8 V or higher) for 1 second.

·

When there is a fluid temperature sensor power supply voltage malfunction.


·

Harness or connector

·

Height control pump and motor (Fluid temperature sensor)

·

Suspension control ECU



WIRING DIAGRAM

C176910E01
5.178,2.206 6.787,2.418 1.609,0.211 10 Suspension Control ECU 5.178,2.035 5.466,2.187 0.288,0.152 10 K35 5.56,0.593 6.049,0.762 0.489,0.170 10 TOIL 5.567,1.503 6.105,1.686 0.538,0.184 10 STG 5.166,0.466 5.419,0.653 0.253,0.187 10 17 5.166,1.376 5.419,1.563 0.253,0.187 10 18 1.426,1.371 1.744,1.575 0.318,0.205 10 SBL 1.361,0.472 1.720,0.633 0.360,0.161 10 TOIL 1.846,1.362 1.995,1.574 0.149,0.211 10 1 1.864,0.456 2.013,0.668 0.149,0.211 10 2 0.53,2.303 2.241,2.506 1.711,0.202 10 Fluid Temperature Sensor 0.53,2.135 0.690,2.291 0.160,0.156 10 i1

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (See page Suspension>SUSPENSION CONTROL>ACTIVE HEIGHT CONTROL SUSPENSION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (OIL TEMPERATURE SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and the tester on.


c.

Select the Data List mode on the intelligent tester.


d.

Check the fluid temperature value of the temperature sensor displayed on the intelligent tester.

AHC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Temperature Sensor Fluid temperature sensor reading /
min.: -3276.8°C (-5866.24°F)
max.: 3276.7°C (5930.06°F)
Actual fluid temperature -

OK:

Same as actual fluid temperature




OK

2.RECONFIRM DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - SUSPENSION CONTROL ECU)
2.RECONFIRM DTC OUTPUT

b.

Perform a road test.


c.

Check for DTCs.

Result
Result Proceed to
DTC C1719 is output A
DTC C1719 is not output B



A

REPLACE SUSPENSION CONTROL ECU

B

3.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - SUSPENSION CONTROL ECU)
NOTICE:

When inspecting the wire harness between the suspension control ECU and temperature sensor, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect the connectors for the temperature sensor, the acceleration sensors (front RH, front LH) and pressure accumulator sensor on the ECU side.


a.

Disconnect the K34 and K35 ECU connectors.


b.

Disconnect the i1 sensor connector.

U164788E02
1.896,1.979 2.208,2.208 2.208,2.208 2.208,2.271 true 1.844,1.979 0.958,2.167 0.958,2.167 0.958,2.24 true 5.167,1.75 4.677,2.104 4.677,2.104 4.677,2.177 true 5.5,1.76 6.031,2.135 6.031,2.135 6.031,2.198 true 0.708,0.115 3.021,0.521 2.313,0.406 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.323,0.083 6.729,0.604 2.406,0.521 10 false Front view of wire harness connector: (to Fluid Temperature Sensor) 1.146,1.677 1.427,1.885 0.281,0.208 10 false K35 2.292,1.677 2.656,1.917 0.365,0.24 10 false K34 1.969,2.354 2.604,2.552 0.635,0.198 10 false 17 (TOIL) 0.698,2.333 1.427,2.542 0.729,0.208 10 false 18 (STG) 4.458,1.583 4.646,1.74 0.188,0.156 10 false i1 4.552,2.229 5.031,2.49 0.479,0.26 10 false SBL 5.906,2.24 6.458,2.479 0.552,0.24 10 false TOIL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K35-17 (TOIL) - i1-2 (TOIL) Always Below 1 Ω
K35-17 (TOIL) - Body ground Always 10 kΩ or higher
K35-18 (STG) - i1-1 (SBL) Always Below 1 Ω
K35-18 (STG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FLUID TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FLUID TEMPERATURE SENSOR
a.

Connect the i2 temperature sensor connector.


b.

Disconnect the K34 and K35 ECU connectors.


U164844E02
1.698,2.563 2.229,2.813 2.229,2.813 2.229,2.927 true 1.635,2.563 0.688,2.833 0.688,2.833 0.688,2.917 true 0.24,0.146 2.729,0.688 2.49,0.542 10 false Rear view of wire harness connector: (to Suspension Control ECU) 1.865,2.958 2.531,3.135 0.667,0.177 10 false 17 (TOIL) 0.323,2.948 1.052,3.135 0.729,0.188 10 false 18 (STG) 0.75,2.281 1.063,2.469 0.313,0.188 10 false K35 2.219,2.281 2.51,2.469 0.292,0.188 10 false K34

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K35-17 (TOIL) - K35-18 (STG) 20°C (68°F) 2.32 to 2.59 kΩ




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE HEIGHT CONTROL PUMP AND MOTOR