Home › Suspension › SUSPENSION CONTROL › DAMPING FORCE CONTROL ACTUATOR(for Rear Side)
RM2660E _53 Suspension _052813 SUSPENSION CONTROL _0255379 DAMPING FORCE CONTROL ACTUATOR(for Rear Side) A

SUSPENSION CONTROL  DAMPING FORCE CONTROL ACTUATOR(for Rear Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 491B1 1.INSTALL REAR NO. 2 SUSPENSION CONTROL ACCUMULATOR BRACKET LH

a.

Install the bracket to the shock absorber control valve with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 48040 2.INSTALL REAR SHOCK ABSORBER CONTROL VALVE ASSEMBLY LH

a.
C172669

Install the bracket to the control valve with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.
C172668

Install the control valve together with the bracket to the vehicle with the 3 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


c.

Connect the control valve connector.


d.
C172804E01
0.141,3.955 2.777,4.111 2.637,0.156 10 No. 4 Suspension Control Pressure Hose 1.741,2.761 1.741,3.897 false 0.668,3.42 1.192,3.582 0.524,0.162 10 Gasket 0.973,2.905 0.973,3.411 false 2.725,0.691 3.254,0.834 0.528,0.143 10 Bracket 2.688,0.766 1.835,0.766 false 0.936,0.133 2.814,0.288 1.878,0.155 10 Shock Absorber Control Valve 1.291,2.011 0.46,0.992 false 0.46,0.992 0.46,0.202 false 0.46,0.202 0.89,0.202 false 1.835,0.766 1.835,1.508 false

Connect the wire harness clamp to the control valve bracket.


e.

Install a new gasket to the No. 4 suspension control pressure hose, and connect the hose to the control valve with the union bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


f.
C178069E01
1.208,3.378 2.199,3.548 0.991,0.170 10 Fulcrum Length 0.608,3.888 2.256,4.058 1.648,0.170 10 No. 4 Height Control Tube 0.541,3.974 0.155,3.974 false 0.155,3.974 0.155,2.762 false 0.155,2.762 0.727,0.474 false

Using a union nut wrench, connect the No. 4 height control tube to the control valve.

Torque:
without union nut wrench : 44 N*m (450 kgf*cm, 33 ft.*lbf)
with union nut wrench : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

·

The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.




Hide 49158D 3.INSTALL REAR NO. 3 SUSPENSION CONTROL ACCUMULATOR LH

a.

Apply a small amount of suspension fluid to a new O-ring and new back-up ring and install them to the accumulator.


b.
C176191

Install the No. 3 control accumulator to the control valve.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)


Hide 49050 4.INSTALL REAR SUSPENSION CONTROL ACCUMULATOR ASSEMBLY LH

a.

Apply a small amount of suspension fluid to a new O-ring and install it to the accumulator.


b.
C179740

Install the control accumulator to the control valve.

Torque:
57 N*m (585 kgf*cm, 42 ft.*lbf)


Hide 489B0 8.INSTALL HEIGHT CONTROL UNIT PROTECTOR ASSEMBLY LH