Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2014.08–2015.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the ECU detects trouble, the tire pressure warning light blinks (illuminates after blinking for 1 minute) and tire pressure monitoring is canceled at the same time. At this time, the ECU stores a DTC in the memory.

Connect terminals TC and CG of the DLC3 to make the tire pressure warning light blink and output the DTC.

WIRING DIAGRAM

C285250E03
0.125,3.375 0.458,3.573 0.333,0.198 10 false L60 0.104,3.542 2.74,3.802 2.635,0.26 10 false Tire Pressure Warning ECU and Receiver 3.198,2.917 4.188,3.146 0.99,0.229 10 false ECU-IG No. 4 4.385,2.75 5.396,2.917 1.01,0.167 10 false from IG Circuit 4.177,1.823 6.125,2.01 1.948,0.188 10 false Combination Meter Assembly 2.042,2.76 2.333,2.979 0.292,0.219 10 false IG1 1.979,1.948 2.344,2.177 0.365,0.229 10 false GN1 2.365,2.635 2.563,2.802 0.198,0.167 10 false 1 2.365,1.823 2.563,1.99 0.198,0.167 10 false 4 0.708,4.01 3.281,4.25 2.573,0.24 10 false : CAN Communication System 4.188,1.656 4.552,1.885 0.365,0.229 10 false E7

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK CAN COMMUNICATION LINE
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: "CAN Bus Check" from the "System Select" screen.


e.

Check the CAN communication system (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM).

OK:

The CAN communication system is normal.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

2.CHECK TIRE PRESSURE WARNING LIGHT CONDITION

B

C

2.CHECK TIRE PRESSURE WARNING LIGHT CONDITION
a.

Check for tire pressure warning light condition.

Result:
Result Proceed to
Tire pressure warning light does not illuminate despite tire pressure decreasing A
Tire pressure warning light remains illuminated (goes off during initial check) B
Tire pressure warning light remains illuminated (illuminates during initial check) C




A

3.PERFORM INSPECTION CHECK NECESSARY FOR SYMPTOM

B

5.CHECK IF TIRE PRESSURE WARNING ECU AND RECEIVER CONNECTOR IS SECURELY CONNECTED

C

3.PERFORM INSPECTION CHECK NECESSARY FOR SYMPTOM
NOTICE:

If the following checks in the Suspected Area column of the Problem Symptoms Table have not been performed, make sure to perform the following checks before proceeding (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>PROBLEM SYMPTOMS TABLE).

If the items below are normal, proceed to the next step.

·

Initialization

·

Check Data List (ID Tire Inflation Pressure)

·

ID code check (Registration)




NEXT

4.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
4.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the condition of the tire pressure warning light by operating the GTS.

Combination Meter
Tester Display Test Part Control Range
Indicat. Tire Pressure Warning System Tire Pressure Warning Light OFF or ON

OK:

The warning light turns on when operating the GTS.




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

5.CHECK IF TIRE PRESSURE WARNING ECU AND RECEIVER CONNECTOR IS SECURELY CONNECTED
a.

Check if the tire pressure warning ECU and receiver connector is securely connected.

OK:

The connector is securely connected.




OK

6.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR TO TIRE PRESSURE WARNING ECU AND RECEIVER CORRECTLY

6.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - BATTERY AND BODY GROUND)
a.
U165432E02
0.708,0.583 0.875,0.583 0.875,0.583 0.885,1.031 true 0.875,1.406 0.875,1.781 true 0.438,0.5 0.698,0.667 0.26,0.167 10 false IG1 0.094,0.021 0.344,0.208 0.25,0.188 10 false *a 0.698,1.844 1.031,2 0.333,0.156 10 false GN1 1.573,0.5 1.917,0.667 0.344,0.167 10 false L60

Disconnect the tire pressure warning ECU and receiver L60 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L60-1 (IG1) - Body ground Engine switch on (IG) 10 to 16 V
Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-4 (GN1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR