Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2014.08–2015.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2195/95  Multi-receiver Antenna Circuit (Test Mode DTC)  


DESCRIPTION

This DTC is used for detecting open circuits and radio wave frequency mismatches in the tire pressure warning antenna.

DTC No. DTC Detection Condition Trouble Area
C2195/95 Test mode procedure is performed.
·

Tire pressure warning antenna (for Rear side)

·

Tire pressure warning antenna (for Front side)

·

Harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C272092E11
4.75,3.427 6.854,3.823 2.104,0.396 10 false Tire Pressure Warning ECU and Receiver 2.073,1.24 3.74,1.646 1.667,0.406 10 false Tire Pressure Warning Antenna (for Rear Side) 0.208,2.906 1.938,3.26 1.729,0.354 10 false Tire Pressure Warning Antenna (for Front Side) 0.927,2.406 1.354,2.583 0.427,0.177 10 false FR1 1.469,2.135 1.708,2.344 0.24,0.208 10 false 1 5.979,2.365 6.458,2.531 0.479,0.167 10 false EC2 5.74,2.146 5.885,2.323 0.146,0.177 10 false 8 4.75,3.219 5.115,3.406 0.365,0.188 10 false L60 5.958,0.625 6.438,0.792 0.479,0.167 10 false EC3 5.74,0.406 5.885,0.583 0.146,0.177 10 false 9 2.99,0.646 3.344,0.792 0.354,0.146 10 false RR1 3.417,0.417 3.583,0.573 0.167,0.156 10 false 1 2.073,1.052 2.396,1.219 0.323,0.167 10 false L59 0.208,2.729 0.531,2.885 0.323,0.156 10 false A64 4.24,0.854 4.823,1.021 0.583,0.167 10 false Shielded 3.438,2.573 4.021,2.74 0.583,0.167 10 false Shielded 3.563,2.177 3.885,2.323 0.323,0.146 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - TIRE PRESSURE WARNING ANTENNA)
a.

Disconnect the tire pressure warning ECU and receiver L60 connector.


b.

Disconnect the tire pressure warning antenna (for Rear Side) L59 connector.


c.

Disconnect the tire pressure warning antenna (for Front Side) A64 connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

Because the coaxial cable that is used for the tire pressure warning antenna consists of a center conductor and an outer shielding layer (-), this measurement should be performed to ensure that there is no malfunction in the coaxial cable.


Standard Resistance:
Tester Connection Condition Specified Condition
L60-9 (EC3) - L59-1 (RR1) Always Below 1 Ω
L60-8 (EC2) - A64-1 (FR1) Always Below 1 Ω
L60-9 (shielded wire) - L59-1 (shielded wire) Always Below 1 Ω
L60-8 (shielded wire) - A64-1 (shielded wire) Always Below 1 Ω
L60-9 (EC3) - L59-1 (shielded wire) Always 10 kΩ or higher
L60-8 (EC2) - A64-1 (shielded wire) Always 10 kΩ or higher
L60-9 (shielded wire) - L59-1 (RR1) Always 10 kΩ or higher
L60-8 (shielded wire) - A64-1 (FR1) Always 10 kΩ or higher




OK

2.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION (for Rear Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION (for Rear Side)
a.

Set the tire pressure to the specified value (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).


b.

Turn the engine switch off.


c.

Disconnect the tire pressure warning antenna (for Front Side) A64 connector.

NOTICE:

Be sure to disconnect the connector on the tire pressure warning antenna.



d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG).


f.

Turn the GTS on.


g.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


h.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*

HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




i.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

i.

Check that each tire pressure data displayed on the GTS has changed.

Result:
Result Proceed to
Tire pressure data does not change A
Tire pressure of at least 1 wheel changes B





A

3.REPLACE TIRE PRESSURE WARNING ANTENNA (for Rear Side)

B

4.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION (for Front Side)
3.REPLACE TIRE PRESSURE WARNING ANTENNA (for Rear Side)
a.

Replace the tire pressure warning antenna (for Rear Side) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING ANTENNA(for Rear Side)>REMOVAL).



NEXT

4.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION (for Front Side)
4.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION (for Front Side)
a.

Set the tire pressure to the specified value (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).


b.

Turn the engine switch off.


c.

Connect the tire pressure warning antenna (for Front Side) A64 connector.


d.

Disconnect the tire pressure warning antenna (for Rear Side) L59 connector.

NOTICE:

Be sure to disconnect the connector on the tire pressure warning antenna.



e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


i.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure/
min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*

HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




j.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

i.

Check that each tire pressure data displayed on the GTS has changed.

Result:
Result Proceed to
Tire pressure data does not change A
Tire pressure of at least 1 wheel changes B





A

5.REPLACE TIRE PRESSURE WARNING ANTENNA (for Front side)

B

6.CHECK TEST MODE DTC (C2195/95)
5.REPLACE TIRE PRESSURE WARNING ANTENNA (for Front side)
a.

Replace the tire pressure warning antenna (for Front Side) (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING ANTENNA(for Front Side)>REMOVAL).



NEXT

6.CHECK TEST MODE DTC (C2195/95)
6.CHECK TEST MODE DTC (C2195/95)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.


f.

Perform the test mode inspection (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE).

Result:
Result Proceed to
DTC C2195/95 is not cleared A
DTC 2195/95 is cleared (When performing the test mode inspection after replacing the tire pressure warning antenna (for Rear Side) or tire pressure warning antenna (for Front Side)) B
DTC 2195/95 is cleared (When performing the test mode inspection after the tire pressures have changed as a result of the tire pressure warning antenna reception (for Front Side and Rear Side) check) C




A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END

C