Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Skid Control Buzzer Circuit  


DESCRIPTION

The skid control buzzer sounds upon receiving a signal from the skid control ECU (master cylinder solenoid).

WIRING DIAGRAM

C173348E23
2.365,2.063 3.354,2.292 0.99,0.229 10 false from IG Circuit 1.688,1.24 2.708,1.417 1.021,0.177 10 false ECU-IG No. 1 3.198,0.948 3.313,1.115 0.115,0.167 10 false 2 3.302,1.583 4.771,1.854 1.469,0.271 10 false Skid Control Buzzer 5.813,1.063 6.115,1.271 0.302,0.208 10 false BZ 5.542,0.927 5.917,1.115 0.375,0.188 10 false 30 5.427,3.156 7.104,3.594 1.677,0.438 10 false Skid Control ECU (Master Cylinder Solenoid) 4.146,0.948 4.26,1.115 0.115,0.167 10 false 1 5.438,3 5.781,3.177 0.344,0.177 10 false A24 3.302,1.417 3.688,1.625 0.385,0.208 10 false E5 3.385,1.063 3.677,1.24 0.292,0.177 10 false IG1 3.844,1.063 4.135,1.24 0.292,0.177 10 false BZ

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DSS SIGNAL BUZZER)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
DSS Signal Buzzer Skid control buzzer Buzzer ON/OFF The buzzer can be heard.


f.

Check that the skid control buzzer sounds/stops when turning the skid control buzzer on/off by using the GTS.

Result
Result Proceed to
Buzzer does not sound or sounds constantly A
Buzzer sounds/stops B



A

2.CHECK TERMINAL VOLTAGE (IG1)

B

2.CHECK TERMINAL VOLTAGE (IG1)
a.

Turn the ignition switch off.


b.

Disconnect the skid control buzzer assembly connector.


c.
U164990E02
1.948,1.479 2.552,1.615 2.552,1.615 2.552,1.74 true 1.635,0.354 1.906,0.542 0.271,0.188 10 false E5 0.156,0.094 0.427,0.302 0.271,0.208 10 false *a 2.448,1.802 2.708,1.969 0.26,0.167 10 false IG1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E5-2 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)



OK

3.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SKID CONTROL BUZZER
a.

Remove the skid control buzzer assembly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>SKID CONTROL BUZZER>REMOVAL).


b.
C358474E01
1.281,1.302 1.281,1.208 1.281,1.208 2.01,0.99 true 2.333,0.927 3.021,1.031 3.021,1.031 3.021,1.115 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.219,1.333 1.469,1.531 0.25,0.198 10 false BZ 2.948,1.167 3.26,1.365 0.313,0.198 10 false IG1

Apply battery voltage to the skid control buzzer, and check that the buzzer sounds.

OK:
Measurement Condition Specified Condition
Battery positive (+) voltage - Terminal 2 (IG1) Skid control buzzer sounds
Battery negative (-) voltage - Terminal 1 (BZ)


Text in Illustration
*a Component without harness connected
(Skid Control Buzzer Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - SKID CONTROL ECU)

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - SKID CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the E5 skid control buzzer assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (BZ) - E5-1 (BZ) Always Below 1 Ω
A24-30 (BZ) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C