Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.08–2017.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

The DTCs are output by the blinking of the ABS warning light and slip indicator light.

WIRING DIAGRAM

C256466E34
5.365,1.49 6.979,1.917 1.615,0.427 10 false Skid Control ECU (Master Cylinder Solenoid) 3.667,2.74 4.01,2.948 0.344,0.208 10 false E22 3.667,2.906 4.156,3.188 0.49,0.281 10 false DLC3 3.615,2.156 3.865,2.313 0.25,0.156 10 false CG 3.615,1.729 3.844,1.885 0.229,0.156 10 false TC 0.354,2.99 0.823,3.188 0.469,0.198 10 false ECM 0.906,1.729 1.167,1.958 0.26,0.229 10 false TC 1.021,4.229 3.052,4.448 2.031,0.219 10 false : CAN Communication System 1.198,1.604 2.438,1.844 1.24,0.24 10 false 16*1, 27*2, 43*5 3.354,1.635 3.552,1.833 0.198,0.198 10 false 13 3.417,2.052 3.594,2.25 0.177,0.198 10 false 4 0.333,2.76 1.427,2.958 1.094,0.198 10 false A38*3, A52*4 5.385,1.302 5.677,1.542 0.292,0.24 10 false A24 1.052,3.333 3.083,3.552 2.031,0.219 10 false *1: for 1UR-FE and 1GR-FE 1.052,3.594 3.083,3.813 2.031,0.219 10 false *2: for 1VD-FTV 3.333,3.333 4.219,3.583 0.885,0.25 10 false *3: for LHD 3.333,3.583 4.24,3.813 0.906,0.229 10 false *4: for RHD 3.333,3.833 4.458,4.125 1.125,0.292 10 false *5: for 3UR-FE

HINT:

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT DLC3 (DLC3 (TC) - DLC3 (CG))
a.
U156266E03
1.771,0.208 1.625,0.208 1.625,0.208 1.625,0.813 true 1.667,1.948 1.844,1.948 1.844,1.948 1.844,1.5 true 0.094,0.125 0.302,0.354 0.208,0.229 10 false *1 0.146,1.333 0.469,1.573 0.323,0.24 10 false E22 1.833,0.125 2.104,0.281 0.271,0.156 10 false CG 1.406,1.875 1.646,2.042 0.24,0.167 10 false TC

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E22-13 (TC) - E22-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*1 DLC3



OK

2.CHECK CAN COMMUNICATION LINE

NG

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))
4.CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))
a.

Turn the ignition switch off.


b.

for LHD:

i.

Disconnect the A38 ECM connector.



c.

for RHD:

i.

Disconnect the A52 ECM connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD (1UR-FE):
Tester Connection Condition Specified Condition
A38-16 (TC) - E22-13 (TC) Always Below 1 Ω

for RHD (1UR-FE):
Tester Connection Condition Specified Condition
A52-16 (TC) - E22-13 (TC) Always Below 1 Ω

for LHD (1VD-FTV):
Tester Connection Condition Specified Condition
A38-27 (TC) - E22-13 (TC) Always Below 1 Ω

for RHD (1VD-FTV):
Tester Connection Condition Specified Condition
A52-27 (TC) - E22-13 (TC) Always Below 1 Ω

for 1GR-FE
Tester Connection Condition Specified Condition
A38-16 (TC) - E22-13 (TC) Always Below 1 Ω

for 3UR-FE
Tester Connection Condition Specified Condition
A38-43 (TC) - E22-13 (TC) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)
a.
U156269E02
1.771,0.198 1.625,0.198 1.625,0.198 1.625,0.802 true 0.094,0.083 0.302,0.313 0.208,0.229 10 false *1 0.146,1.333 0.438,1.51 0.292,0.177 10 false E22 1.823,0.115 2.094,0.271 0.271,0.156 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

6.CHECK ECM (DLC3 (TC) INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (DLC3 (TC) INPUT)
a.
U156266E03
1.771,0.208 1.625,0.208 1.625,0.208 1.625,0.813 true 1.667,1.948 1.844,1.948 1.844,1.948 1.844,1.5 true 0.094,0.125 0.302,0.354 0.208,0.229 10 false *1 0.146,1.333 0.469,1.573 0.323,0.24 10 false E22 1.833,0.125 2.104,0.281 0.271,0.156 10 false CG 1.406,1.875 1.646,2.042 0.24,0.167 10 false TC

Using SST, connect terminals TC and CG of the DLC3.


b.

Check that the malfunction indicator lamp is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B

Text in Illustration
*1 DLC3



A

7.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

REPAIR OR REPLACE WIRE HARNESS OR ECM

7.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.





g.

for RHD (without Central Gateway ECU):

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
CAN system DTC is not output (for LHD) A
CAN system DTC is not output (for RHD) B
CAN system DTC is output C

HINT:




A

B

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)