Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The slip indicator light blinks during VSC, A-TRC, Crawl Control and hill-start assist control operation.

When the system fails, the slip indicator light comes on to warn the driver.

WIRING DIAGRAM

C257192E13
5.188,2.083 5.49,2.26 0.302,0.177 10 false A24 5.188,2.313 6.896,2.781 1.708,0.469 10 false Skid Control ECU (Master Cylinder Solenoid) 0.333,2.438 0.656,2.688 0.323,0.25 10 false E7 0.323,2.646 2.208,2.896 1.885,0.25 10 false Combination Meter Assembly 0.646,3.208 2.667,3.479 2.021,0.271 10 false : CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK CAN COMMUNICATION LINE

A

5.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

5.CHECK DTC (CAN COMMUNICATION SYSTEM)

A

6.PERFORM ACTIVE TEST USING GTS (SLIP INDICATOR LIGHT)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.PERFORM ACTIVE TEST USING GTS (SLIP INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe the combination meter.


f.

When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Slip Indicator Light Slip indicator light/ ON or OFF ON: Indicator light on
OFF: Indicator light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C