If the voltage supplied to the IG1 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1241 | Either condition is met:
1. Both of the following conditions continue for at least 10 seconds. ·
The vehicle speed is more than 3 km/h (2 mph). ·
The IG1 terminal voltage is below 9.5 V. 2. All of the following conditions continue for at least 0.2 seconds. ·
The solenoid relay remains on. ·
The IG1 terminal voltage is below 9.5 V. ·
The relay contact is open. |
·
Battery ·
ECU-IG No. 2 fuse ·
Charging system ·
Harness or connector ·
Skid control ECU (Master cylinder solenoid) |
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG1 Voltage Value | IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | - |
Check the voltage output from the skid control ECU (master cylinder solenoid) displayed on the GTS.
The output voltage displayed on the GTS is within 11 to 14 V.
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output (for LHD) | A |
| DTC is output (for RHD) | B |
| DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) | C |
| DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) | D |
A
B
C
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
D
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A24-46 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid)) |
OK
NG
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
| Result | Proceed to |
|---|---|
| DTC is output (for LHD) | A |
| DTC is output (for RHD) | B |
| DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) | C |
| DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) | D |
A
B
C
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
D