Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering sensor signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering sensor power supply malfunction signal is received from the steering sensor.
·

ECU-B1 fuse

·

ECU-IG No. 2 fuse

·

Steering sensor power supply

·

Steering sensor

·

Steering control ECU (w/ VGRS)



WIRING DIAGRAM

C257149E04
4.833,3.75 6.156,3.969 1.323,0.219 10 false Steering Sensor 0.563,3.583 3.417,3.802 2.854,0.219 10 false Skid Control ECU (Master Cylinder Solenoid) 1.323,2.385 2.385,2.615 1.063,0.229 10 false from IG Circuit 1.104,0.333 2.135,0.656 1.031,0.323 10 false from Battery 3.146,2.583 4.135,2.833 0.99,0.25 10 false ECU-IG No.2 2.552,0.531 3.344,0.771 0.792,0.24 10 false ECU-B1 4.885,2.823 5.156,3.042 0.271,0.219 10 false IG 5.844,2.833 6.271,3.063 0.427,0.229 10 false BAT 5.948,3.219 6.438,3.5 0.49,0.281 10 false ESS 5,2.594 5.292,2.802 0.292,0.208 10 false 1 6.021,2.594 6.354,2.792 0.333,0.198 10 false 3 6.385,3.083 6.781,3.313 0.396,0.229 10 false 2 0.906,4.385 3.021,4.615 2.115,0.229 10 false : CAN Communication System 4.844,3.594 5.219,3.844 0.375,0.25 10 false E11 0.563,3.427 0.979,3.656 0.417,0.229 10 false A24 3.76,1.552 5.219,1.813 1.458,0.26 10 false Steering Control ECU*2 5.115,1.146 5.625,1.385 0.51,0.24 10 false E79 4.74,1.156 5.188,1.417 0.448,0.26 10 false +BO 5.198,0.958 5.469,1.135 0.271,0.177 10 false 1 4.375,0.198 4.604,0.375 0.229,0.177 10 false *1 0.333,4.76 1.281,5 0.948,0.24 10 false *1: w/o VGRS 3.333,0.719 3.594,0.938 0.26,0.219 10 false *2 0.333,5.031 1.26,5.26 0.927,0.229 10 false *2: w/ VGRS 3.865,1.146 4.344,1.333 0.479,0.188 10 false +BI 3.531,1.146 3.969,1.365 0.438,0.219 10 false E77 3.573,0.969 3.76,1.125 0.188,0.156 10 false 10 5.542,1.823 5.875,2.073 0.333,0.25 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the steering sensor, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the speed sensor or the yaw rate sensor assembly has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor assembly are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.


PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for LHD) C



A

2.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

Disconnect the steering sensor connector.


U164481E02
1.021,1.417 0.448,1.417 true 1.198,1.469 1.198,1.885 1.198,1.885 1.344,1.885 true 1.583,0.583 1.865,0.75 0.281,0.167 10 false E11 0.135,0.083 0.406,0.323 0.271,0.24 10 false *a 0.229,1.344 0.5,1.573 0.271,0.229 10 false IG 1.396,1.802 1.844,1.99 0.448,0.188 10 false ESS

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E11-1 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-2 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)


OK

3.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering sensor connector.


U164482E02
1.354,1.469 1.354,1.885 1.354,1.885 1.5,1.885 true 1.583,0.573 1.865,0.74 0.281,0.167 10 false E11 0.125,0.073 0.396,0.313 0.271,0.24 10 false *a 1.552,1.802 1.927,1.979 0.375,0.177 10 false BAT

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E11-3 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)

Result
Result Proceed to
OK A
NG (w/ VGRS) B
NG (w/o VGRS) C



A

B

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering control ECU connector.


U164486E02
2.49,1.375 2.823,1.375 true 0.177,0.104 0.385,0.313 0.208,0.208 10 false *a 1.615,0.271 1.938,0.479 0.323,0.208 10 false E77 2.885,1.281 3.188,1.469 0.302,0.188 10 false +BI

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E77-10 (+BI) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)



OK

5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the E11 steering sensor connector.


c.

Disconnect the E79 steering control ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-3 (BAT) - E79-1 (+BO) Always Below 1 Ω
E11-3 (BAT) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C