Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU (master cylinder solenoid), the relay contact turns on and the stop light comes on.

DTC Code DTC Detection Condition Trouble Area
C1380 Either condition is met:
1.

When the voltage at the IG1 terminal is between 11 and 14 V and the stop light control relay drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.

2.

When the voltage at the IG1 terminal is between 11 and 14 V and the stop light control relay drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.


·

Pre-crash safety system

·

STOP fuse

·

Harness or connector

·

STP LP OPE relay (Brake light relay)

·

Stop light control relay assembly

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C246900E12
3.521,2.656 5.802,2.865 2.281,0.208 10 false Stop Light Control Relay Assembly 0.938,0.563 1.344,0.74 0.406,0.177 10 false STOP 3.219,0.396 4.052,0.656 0.833,0.26 10 false from Battery 3.563,2.01 3.74,2.219 0.177,0.208 10 false 8 3.563,1.688 3.74,1.875 0.177,0.188 10 false 6 3.833,1.781 4.156,1.979 0.323,0.198 10 false +B 4.604,1.958 4.969,2.156 0.365,0.198 10 false GND 4.208,1.448 4.344,1.625 0.135,0.177 10 false 2 4.25,1.698 4.552,1.854 0.302,0.156 10 false STP 0.771,2.281 1.792,2.49 1.021,0.208 10 false ENG-IG NO. 1 5.083,1.844 5.229,2.031 0.146,0.188 10 false 4 3.823,2.104 4.156,2.313 0.333,0.208 10 false OUT 1.729,1.365 3.563,1.573 1.833,0.208 10 false Stop Light Switch Assembly 2.958,0.771 3.115,0.969 0.156,0.198 10 false 2 1.74,0.771 1.948,0.958 0.208,0.188 10 false 1 3.25,5.646 4.167,5.844 0.917,0.198 10 false to Stop Lights 5.958,5.25 6.375,5.438 0.417,0.188 10 false STP2 5.979,0.865 6.313,1.031 0.333,0.167 10 false STP 5.667,0.76 5.854,0.958 0.188,0.198 10 false 7 5.656,5.135 5.865,5.313 0.208,0.177 10 false 45 5.948,3.854 6.448,4.021 0.5,0.167 10 false STPO 5.646,3.74 5.854,3.906 0.208,0.167 10 false 16 2.917,3.104 3.073,3.313 0.156,0.208 10 false 4 5.323,5.833 7.042,6.188 1.719,0.354 10 false Skid Control ECU (Master Cylinder Solenoid) 5.344,5.635 5.688,5.792 0.344,0.156 10 false A24 3.531,2.479 3.854,2.646 0.323,0.167 10 false A39 1.74,1.188 2.031,1.365 0.292,0.177 10 false A73 2.073,2.094 3.156,2.281 1.083,0.188 10 false from IG Circuit 2.927,3.74 3.063,3.927 0.135,0.188 10 false 2 1.75,3.74 1.885,3.927 0.135,0.188 10 false 1 1.75,3.26 1.885,3.427 0.135,0.167 10 false 3 2.917,3.427 3.052,3.625 0.135,0.198 10 false 5 1.313,4.26 3.833,4.448 2.521,0.188 10 false STP LP OPE Relay (Brake Light Relay) 1.135,5.844 1.438,6.052 0.302,0.208 10 false K33 1.323,5.552 1.479,5.75 0.156,0.198 10 false 1 1.969,5.542 2.115,5.74 0.146,0.198 10 false 2 1.125,6.052 2.281,6.26 1.156,0.208 10 false Diode (Stop Light) 2.719,0.771 2.865,0.958 0.146,0.188 10 false L 1.958,0.771 2.115,0.979 0.156,0.208 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.CHECK PRE-CRASH SAFETY SYSTEM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch off.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


e.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

B

GO TO PRE-CRASH SAFETY SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
U156220E02
1.688,1.125 2.458,0.667 true 0.281,0.698 0.552,0.865 0.271,0.167 10 false A24 0.167,0.083 0.469,0.344 0.302,0.26 10 false *a 2.51,0.563 2.865,0.75 0.354,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP TERMINAL)

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

REPLACE MASTER CYLINDER SOLENOID

C

REPLACE MASTER CYLINDER SOLENOID