Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for LHD)
RM2660E _54 Brake _052820 BRAKE SYSTEM (OTHER) _0255426 HYDRAULIC BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure not to allow the pump to contact the floor; support it with the booster body. If the pump contacts the floor, the red brake tube between the pump and booster body may be deformed, the operating sound of the pump may become loud enough to hear within the cabin, and fluid may leak.

·

When installing, coat the parts indicated by arrows with lithium soap base glycol grease (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>COMPONENTS).

·

As high pressure is applied to the brake actuator tube No. 1, never deform it.

·

Until the work is over, do not turn the ignition switch on.

·

Before starting the work, make sure that the ignition switch is off and depress the brake pedal more than 20 times.



HINT:

When pressure in the power supply system is released, the reaction force becomes light and the stroke becomes longer.


PROCEDURE

Hide 1.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes into contact with a painted surface.


Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55606 5.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432D 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 10.REMOVE HYDRAULIC BRAKE BOOSTER ASSEMBLY

a.
C172194

Disconnect the 3 connectors from the hydraulic brake booster assembly.


b.
F051200E14
1.198,1.167 1.198,0.74 1.198,0.74 0.698,0.74 true 1.594,1.521 1.594,0.104 1.594,0.104 1.281,0.104 true 2.042,1.729 2.302,0.135 2.302,0.135 2.385,0.135 true 2.479,1.823 2.688,0.896 2.688,0.896 2.802,0.896 true 0.031,0.646 0.802,1.021 0.771,0.375 10 true to Right Rear Wheel 0.583,0.01 1.396,0.396 0.813,0.385 10 true to Right Front Wheel 2.438,0.031 3.24,0.406 0.802,0.375 10 true to Left Front Wheel 2.844,0.813 3.365,1.365 0.521,0.552 10 true to Left Rear Wheel

Use tags or make a memo to identify the place to reconnect.


c.
C172195E02
1.219,1.448 2.313,1.156 2.313,1.156 2.625,1.156 true 2.646,1.073 3.344,1.469 0.698,0.396 10 true Union Nut Wrench

Using a union nut wrench, disconnect the 4 brake lines from the hydraulic brake booster assembly.


d.
C177106E01
0.034,0.006 2.153,0.203 2.119,0.198 12 for Automatic Transmission: 0.061,2.292 2.180,2.489 2.119,0.198 12 for Manual Transmission: 1.408,1.666 1.223,1.894 false

Remove the 4 nuts and pull out the hydraulic brake booster assembly.


Hide 44785 11.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the hydraulic brake booster assembly.