The skid control ECU (master cylinder solenoid) has an open detection circuit, which stores this DTC when detecting an open in the stop light switch input line or the ground line of the stop light switch circuit with the stop light switch off (brake pedal not depressed).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1425 | When the IG1 terminal voltage is 9.5 V or more, the skid control ECU detects an open in the STP circuit for 3 seconds or more. | ·
Harness or connector ·
Stop light switch assembly ·
Stop light control relay assembly ·
Skid control ECU (Master cylinder solenoid) |
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check that the stop lights come on when the brake pedal is depressed.
| Result | Proceed to |
|---|---|
| All stop lights illuminate when the brake pedal is depressed. | A |
| All stop lights do not illuminate when the brake pedal is depressed. | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Check the value of Stop Light SW when the brake pedal is depressed.
| Result | Proceed to |
|---|---|
| The value of Stop Light SW is ON | A |
| Other than above | B |
A
B
Check that there is no short to +B in the STP circuit (wire harnesses and connectors).
No short to +B
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-7 (STP) - Body ground | Brake pedal depressed | 8 to 14 V |
| Brake pedal released | Below 1 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
OK
NG
C
Inspect the stop light switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).
The stop light switch assembly is normal.
OK
NG
Turn the engine switch off.
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-7 (STP) - Body ground | Brake pedal depressed | 8 to 14 V |
| Brake pedal released | Below 1 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
OK
NG
Turn the ignition switch off.
Disconnect the stop light control relay assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A39-2 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V |
| *a | Front view of wire harness connector
(to Stop Light Control Relay Assembly) |
OK
NG