Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the yaw rate sensor assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are stored.

These DTCs are also stored when calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1381 At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

ECU-IG No. 2 fuse

·

ECU-B1 fuse

·

Yaw rate sensor assembly

·

Yaw rate sensor assembly power source circuit



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the yaw rate sensor assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (IG/+B TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (IG/+B TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the yaw rate sensor assembly connector.


c.
U164964E02
1.771,1.208 2.438,1.74 true 2.167,1.125 2.563,0.354 2.563,0.354 2.667,0.354 true 0.177,0.104 0.469,0.323 0.292,0.219 10 false *a 2.427,1.76 2.667,1.938 0.24,0.177 10 false IG 0.344,0.719 0.656,0.927 0.313,0.208 10 false E50 2.729,0.271 2.969,0.448 0.24,0.177 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E50-4 (IG) - Body ground Ignition switch ON 11 to 14 V
E50-6 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the yaw rate sensor assembly connector.


U164965E02
1.188,1.177 0.563,1.552 0.563,1.552 0.563,1.688 false 0.156,0.104 0.448,0.323 0.292,0.219 10 false *a 0.406,1.708 0.781,1.885 0.375,0.177 10 false GND 0.344,0.719 0.646,0.885 0.302,0.167 10 false E50

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Reconnect the yaw rate sensor assembly connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.



Result
Result Proceed to
DTC C1381 is not output A
DTC C1381 is output B


A

B