Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1232  Acceleration Sensor Stuck Malfunction  C1234  Yaw Rate Sensor  C1243  Acceleration Sensor Stuck Malfunction  C1244  Open or Short Circuit in Deceleration Sensor Circuit  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  


DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the yaw rate sensor assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

DTC Code DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

ECU-IG No. 2 fuse

·

ECU-B1 fuse

·

Sensor installation

·

Harness or connector

·

Yaw rate sensor assembly

·

CAN communication system


C1234 A sensor malfunction signal is received from the yaw rate sensor.
C1243 Output values of GL1 and GL2 do not change 16 times or more while vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph).
C1244 When either of the following conditions is detected:
·

Both of the following conditions continue for at least 60 seconds.

-

The vehicle is stopped.

-

The difference between GL1 and GL2 does not drop less than 0.4 G after it reaches 0.6 G or more.


·

A data malfunction signal is received from the acceleration sensor.


C1245 The following condition continues for at least 60 seconds.
·

The difference between the values calculated from the acceleration sensor value and vehicle speed exceeds 0.35 G.


C1279 Stored during test mode.

WIRING DIAGRAM

C257278E04
1.594,0.771 2.76,0.948 1.167,0.177 10 false from IG Circuit 3.458,0.969 4.5,1.271 1.042,0.302 10 false ECU-IG No.2 5.281,1.333 5.583,1.531 0.302,0.198 10 false IG 5.375,1.104 5.708,1.333 0.333,0.229 10 false 4 6.083,2 6.615,2.271 0.531,0.271 10 false GND 6.51,1.896 6.833,2.104 0.323,0.208 10 false 1 5.042,2.646 5.469,2.917 0.427,0.271 10 false E50 5.042,2.802 6.969,3.063 1.927,0.26 10 false Yaw Rate Sensor Assembly 0.667,2.052 3.802,2.344 3.135,0.292 10 false Skid Control ECU (Master Cylinder Solenoid) 0.656,1.885 1.125,2.135 0.469,0.25 10 false A24 0.719,3.323 3.177,3.531 2.458,0.208 10 false : CAN Communication System 5.938,1.344 6.323,1.573 0.385,0.229 10 false +B 6.063,1.104 6.375,1.302 0.313,0.198 10 false 6 4.313,0.427 4.99,0.656 0.677,0.229 10 false ECU-B1 2.406,0.26 3.531,0.5 1.125,0.24 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check if DTCs U0073, U0123, C1210 and/or C1336 areoutput.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result
Result Proceed to
DTC U0073, U0123, C1210 and/or C1336 are not output A
DTC U0073 and/or U0123 are output (for LHD) B
DTC U0073 and/or U0123 are output (for RHD) C
DTC C1210 and/or C1336 are output D



A

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

D

2.CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate sensor assembly is installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR (w/ VSC)>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK HARNESS AND CONNECTOR (IG/+B/GND TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG/+B/GND TERMINAL)
a.
C208309C57
1.427,0.25 1.906,0.479 0.479,0.229 0.792,1.667 1.198,1.198 true 1.802,1.177 2.646,1.667 true 2.156,1.094 2.5,0.417 2.5,0.417 2.833,0.417 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.542,0.281 1.927,0.479 0.385,0.198 10 false E50 0.604,1.719 1.021,1.906 0.417,0.188 10 false GND 2.531,1.74 2.948,1.927 0.417,0.188 10 false GND 2.917,0.333 3.333,0.521 0.417,0.188 10 false +B
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


Disconnect the yaw rate sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E50-4 (IG) - Body ground Ignition switch ON 11 to 14 V
E50-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-1 (GND) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR