Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1242  Open Circuit in IG1/IG2 Power Source Circuit  


DESCRIPTION

If there is a problem with the skid control ECU (master cylinder solenoid) power supply circuit, the skid control ECU (master cylinder solenoid) stores DTCs and prohibits operation under the fail-safe function.

If the voltage supplied to the IG2 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1242 The vehicle speed is 3 km/h (2 mph) or more and the voltage at the ECU IG2 terminal remains below 6.5 V for more than 7 seconds.
·

Battery

·

IG2 NO. 1 fuse

·

Charging system

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173290E20
0.406,0.917 1.427,1.219 1.021,0.302 10 false from IG Circuit 3.583,1.094 4.365,1.313 0.781,0.219 10 false IG2 NO. 1 5.75,0.927 6.292,1.208 0.542,0.281 10 false A25 6.125,0.938 6.594,1.219 0.469,0.281 10 false IG2 5.833,0.729 6.229,0.948 0.396,0.219 10 false 1 5.74,3.313 6.24,3.583 0.5,0.271 10 false A25 5.479,4.76 7.146,5.177 1.667,0.417 10 false Skid Control ECU (Master Cylinder Solenoid) 6.125,3.313 6.677,3.563 0.552,0.25 10 false GND3 5.833,3.104 6.198,3.313 0.365,0.208 10 false 4 5.75,1.74 6.271,1.979 0.521,0.24 10 false A24 6.125,1.74 6.615,1.99 0.49,0.25 10 false GND1 5.823,1.531 6.188,1.75 0.365,0.219 10 false 1 5.74,2.521 6.208,2.76 0.469,0.24 10 false A24 6.115,2.521 6.688,2.802 0.573,0.281 10 false GND2 5.802,2.323 6.208,2.563 0.406,0.24 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
C358306E01
0.646,0.552 1.021,0.802 0.375,0.25 1.167,1.229 1.573,0.896 false 0.708,0.594 1.021,0.792 0.313,0.198 10 false A25 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 0.854,1.24 1.167,1.438 0.313,0.198 10 false IG2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A25-1 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C