Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1253  Pump Motor Relay  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).

DTC Code DTC Detection Condition Trouble Area
C1253 There is a motor system circuit (motor input circuit) malfunction.
·

ABS1 fuse

·

Motor relay circuit

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173280E25
4.135,5.396 6.396,5.615 2.26,0.219 10 false Hydraulic Brake Booster Assembly 4.844,4.917 5.729,5.135 0.885,0.219 10 false Pump Motor 5.219,1.656 6.073,1.885 0.854,0.229 10 false Motor Relay 5,0.781 6.188,1 1.188,0.219 10 false Skid Control ECU 3.135,1.698 3.49,1.906 0.354,0.208 10 false A24 3.219,1.479 3.396,1.635 0.177,0.156 10 false 2 3.531,1.583 4.021,1.771 0.49,0.188 10 false +BM1 3.125,2.208 3.458,2.427 0.333,0.219 10 false A25 3.219,2 3.396,2.156 0.177,0.156 10 false 2 3.531,2.104 4.031,2.292 0.5,0.188 10 false +BM2 3.135,2.677 3.469,2.917 0.333,0.24 10 false A24 3.219,2.469 3.396,2.625 0.177,0.156 10 false 1 3.531,2.583 3.979,2.76 0.448,0.177 10 false GND1 3.135,3.198 3.458,3.406 0.323,0.208 10 false A24 3.198,2.99 3.396,3.146 0.198,0.156 10 false 32 3.531,3.083 4.01,3.26 0.479,0.177 10 false GND2 3.135,3.75 3.458,3.969 0.323,0.219 10 false A25 0.26,4.219 1.104,4.5 0.844,0.281 10 false from Battery 1.052,2.354 1.458,2.625 0.406,0.271 10 false ABS1 3.229,3.542 3.406,3.698 0.177,0.156 10 false 4 3.531,3.646 4.021,3.844 0.49,0.198 10 false GND3 4.552,0.26 6.167,0.479 1.615,0.219 10 false Master Cylinder Solenoid 5.01,3.885 5.333,4.063 0.323,0.177 10 false M+1 6.083,3.885 6.438,4.063 0.354,0.177 10 false M+2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON/OFF An operating sound of the motor can be heard.


g.

Check the operating sound of the motor individually when operating it with the GTS.

OK:

An operating sound of the motor can be heard.




OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (+BM1/+BM2 TERMINAL)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

3.CHECK HARNESS AND CONNECTOR (+BM1/+BM2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connectors.


c.
C358313E01
1.49,0.385 1.875,0.656 0.385,0.271 1.51,2.865 1.896,3.135 0.385,0.271 1.854,3.823 2.479,3.5 true 0.427,2.302 0.875,1.406 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.563,0.438 1.875,0.635 0.313,0.198 10 false A24 1.583,2.917 1.896,3.115 0.313,0.198 10 false A25 0.229,2.354 0.656,2.594 0.427,0.24 10 false +BM1 2.552,3.333 2.979,3.563 0.427,0.229 10 false +BM2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (+BM1) - Body ground Always 11 to 14 V
A25-2 (+BM2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C