Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1253  Pump Motor Relay  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).

DTC Code DTC Detection Condition Trouble Area
C1253 There is a motor system circuit (motor input circuit) malfunction.
·

ABS NO. 1 fuse

·

Motor relay circuit

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173280E27
0.25,4.24 1.115,4.51 0.865,0.271 10 false from Battery 0.958,2.396 1.729,2.615 0.771,0.219 10 false ABS NO. 1 3.24,1.49 3.375,1.698 0.135,0.208 10 false 2 3.135,1.677 3.448,1.896 0.313,0.219 10 false A24 3.51,1.583 4.021,1.792 0.51,0.208 10 false +BM1 4.969,0.802 6.24,1.073 1.271,0.271 10 false Skid Control ECU 5.208,1.677 6.031,1.917 0.823,0.24 10 false Motor Relay 4.51,0.281 6.25,0.531 1.74,0.25 10 false Master Cylinder Solenoid 3.24,2.479 3.375,2.688 0.135,0.208 10 false 1 3.51,2.573 3.979,2.76 0.469,0.188 10 false GND1 3.208,2.99 3.375,3.198 0.167,0.208 10 false 32 3.51,3.083 3.99,3.302 0.479,0.219 10 false GND2 3.229,3.542 3.396,3.75 0.167,0.208 10 false 4 3.51,3.646 3.979,3.865 0.469,0.219 10 false GND3 4.927,3.885 5.208,4.063 0.281,0.177 10 false M+1 4.844,4.917 5.906,5.177 1.063,0.26 10 false Pump Motor 4.146,5.396 6.708,5.656 2.563,0.26 10 false Hydraulic Brake Booster Assembly 6.125,3.885 6.406,4.063 0.281,0.177 10 false M+2 3.24,2.01 3.375,2.219 0.135,0.208 10 false 2 3.135,2.198 3.427,2.396 0.292,0.198 10 false A25 3.51,2.104 3.99,2.302 0.479,0.198 10 false +BM2 3.146,2.677 3.458,2.896 0.313,0.219 10 false A24 3.146,3.188 3.458,3.406 0.313,0.219 10 false A24 3.146,3.74 3.438,3.938 0.292,0.198 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON/OFF An operating sound of the motor can be heard.


g.

Check the operating sound of the motor individually when operating it with the GTS.

OK:

An operating sound of the motor can be heard.




OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (+BM1/+BM2 TERMINAL)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

3.CHECK HARNESS AND CONNECTOR (+BM1/+BM2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connectors.


c.
C358313E01
1.49,0.385 1.875,0.656 0.385,0.271 1.51,2.865 1.896,3.135 0.385,0.271 1.854,3.823 2.479,3.5 true 0.427,2.302 0.875,1.406 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.563,0.438 1.875,0.635 0.313,0.198 10 false A24 1.583,2.917 1.896,3.115 0.313,0.198 10 false A25 0.229,2.354 0.656,2.594 0.427,0.24 10 false +BM1 2.552,3.333 2.979,3.563 0.427,0.229 10 false +BM2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (+BM1) - Body ground Always 11 to 14 V
A25-2 (+BM2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C