Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

The DTCs are output by the blinking of the ABS warning light.

WIRING DIAGRAM

C256466E06
5.392,1.246 5.679,1.410 0.286,0.164 10 A24 5.392,1.429 7.022,1.800 1.629,0.371 10 Skid Control ECU (Master Cylinder Solenoid) 3.708,2.697 3.985,2.846 0.277,0.149 10 E22 3.708,2.858 4.113,3.006 0.406,0.148 10 DLC3 3.613,2.123 3.863,2.279 0.250,0.156 10 CG 3.438,2.028 3.554,2.188 0.116,0.159 10 4 3.615,1.697 3.844,1.857 0.229,0.159 10 TC 3.361,1.615 3.558,1.778 0.198,0.163 10 13 0.291,2.734 1.190,2.897 0.899,0.163 10 A38*3, A52*4 0.307,2.911 0.682,3.070 0.375,0.159 10 ECM 1.201,1.61 1.946,1.768 0.745,0.158 10 16*1, 27*2 0.906,1.71 1.134,1.863 0.229,0.154 10 TC 1.018,4.21 2.986,4.387 1.968,0.177 10 : CAN Communication System 0.909,3.058 2.836,3.242 1.927,0.184 10 *1: for 1UR-FE and 1GR-FE 0.909,3.364 2.836,3.548 1.927,0.184 10 *2: for 1VD-FTV 0.909,3.621 1.673,3.804 0.764,0.184 10 *3: for LHD 0.909,3.878 2.836,4.061 1.927,0.184 10 *4: for RHD

HINT:

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT DLC3 (DLC3 (TC) - DLC3 (CG))
a.
U156266E03
1.771,0.208 1.625,0.208 1.625,0.208 1.625,0.813 true 1.667,1.948 1.844,1.948 1.844,1.948 1.844,1.5 true 0.094,0.125 0.302,0.354 0.208,0.229 10 false *1 0.146,1.333 0.469,1.573 0.323,0.24 10 false E22 1.833,0.125 2.104,0.281 0.271,0.156 10 false CG 1.406,1.875 1.646,2.042 0.24,0.167 10 false TC

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E22-13 (TC) - E22-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*1 DLC3



OK

2.CHECK CAN COMMUNICATION LINE

NG

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))
2.CHECK CAN COMMUNICATION LINE

A

3.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Check for DTCs (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN system DTC is not output A
CAN system DTC is output (for LHD) B
CAN system DTC is output (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))
a.

Turn the ignition switch off.


b.

for LHD:

Disconnect the A38 ECM connector.


c.

for RHD:

Disconnect the A52 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD (1UR-FE and 1GR-FE)
Tester Connection Condition Specified Condition
A38-16 (TC) - E22-13 (TC) Always Below 1 Ω

for LHD (1VD-FTV)
Tester Connection Condition Specified Condition
A38-27 (TC) - E22-13 (TC) Always Below 1 Ω

for RHD (1UR-FE and 1GR-FE)
Tester Connection Condition Specified Condition
A52-16 (TC) - E22-13 (TC) Always Below 1 Ω

for RHD (1VD-FTV)
Tester Connection Condition Specified Condition
A52-27 (TC) - E22-13 (TC) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)
a.
U156269E02
1.771,0.198 1.625,0.198 1.625,0.198 1.625,0.802 true 0.094,0.083 0.302,0.313 0.208,0.229 10 false *1 0.146,1.333 0.438,1.51 0.292,0.177 10 false E22 1.823,0.115 2.094,0.271 0.271,0.156 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

6.CHECK ECM (DLC3 (TC) INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (DLC3 (TC) INPUT)
a.
U156266E03
1.771,0.208 1.625,0.208 1.625,0.208 1.625,0.813 true 1.667,1.948 1.844,1.948 1.844,1.948 1.844,1.5 true 0.094,0.125 0.302,0.354 0.208,0.229 10 false *1 0.146,1.333 0.469,1.573 0.323,0.24 10 false E22 1.833,0.125 2.104,0.281 0.271,0.156 10 false CG 1.406,1.875 1.646,2.042 0.24,0.167 10 false TC

Using SST, connect terminals TC and CG of the DLC3.


b.

Check that the MIL is blinking.

Result
Result Proceed to
MIL is blinking A
MIL is not blinking B

Text in Illustration
*1 DLC3



A

7.CHECK DTC (CAN COMMUNICATION SYSTEM)

B

REPAIR OR REPLACE WIRE HARNESS OR ECM

7.CHECK DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Check for DTCs (for LHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM, for RHD: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN system DTC is not output (for LHD) A
CAN system DTC is not output (for RHD) B
CAN system DTC is output (for LHD) C
CAN system DTC is output (for RHD) D



A

B

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

D

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)