Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following is detected, the ABS warning light remains on.

·

The skid control ECU (master cylinder solenoid) connector is disconnected from the skid control ECU (master cylinder solenoid).

·

There is a malfunction in the skid control ECU (master cylinder solenoid) internal circuit.

·

There is an open in the harness between the combination meter and skid control ECU (master cylinder solenoid).

·

The anti-lock brake system is defective.

·

The voltage at terminal IG1 is high.

·

The rear differential is locked.*


*: w/ Rear Differential Lock


HINT:

It may not be possible to use the GTS when the skid control ECU (master cylinder solenoid) is abnormal.


WIRING DIAGRAM

C258381E03
2.719,3.51 3.01,3.667 0.292,0.156 10 false RLP 3.094,3.49 3.271,3.646 0.177,0.156 10 false 15 3.375,4.573 5.135,5.094 1.76,0.521 10 false Rear Differential Lock Detection Switch (No. 1 Transfer Indicator switch)* 3.344,3.781 3.469,3.927 0.125,0.146 10 false * 5.51,4.646 7.125,5 1.615,0.354 10 false Skid Control ECU (Master Cylinder Solenoid) 5.417,3.406 5.604,3.552 0.188,0.146 10 false 14 5.74,3.604 6.073,3.76 0.333,0.156 10 false P 1.823,4.083 3.229,4.427 1.406,0.344 10 false 4 Wheel Drive Control ECU 0.135,3.167 2.021,3.438 1.885,0.271 10 false Combination Meter Assembly 0.74,4.75 2.667,4.917 1.927,0.167 10 false : CAN Communication System 0.146,5.135 1.854,5.333 1.708,0.198 10 false *: w/ Rear Differential Lock 2.323,2.875 2.51,3.031 0.188,0.156 10 false IG 5.417,0.573 5.594,0.719 0.177,0.146 10 false 46 5.75,0.771 6.052,0.99 0.302,0.219 10 false IG1 3.458,0.76 4.521,1.042 1.063,0.281 10 false from IG1 Circuit 5.74,1.24 6.188,1.479 0.448,0.24 10 false GND1 5.74,1.719 6.146,1.927 0.406,0.208 10 false GND2 5.74,2.198 6.146,2.417 0.406,0.219 10 false GND3 5.448,1.042 5.563,1.198 0.115,0.156 10 false 1 5.406,1.531 5.594,1.698 0.188,0.167 10 false 32 5.448,2.01 5.625,2.229 0.177,0.219 10 false 4 5.365,0.76 5.677,0.99 0.313,0.229 10 false A24 5.365,1.24 5.656,1.427 0.292,0.188 10 false A24 5.365,1.719 5.698,1.958 0.333,0.24 10 false A24 5.365,2.198 5.677,2.417 0.313,0.219 10 false A25 5.365,3.604 5.646,3.823 0.281,0.219 10 false A24 3.375,4.385 3.615,4.594 0.24,0.208 10 false f2 3.771,4.188 4,4.365 0.229,0.177 10 false +B 3.615,3.969 3.802,4.177 0.188,0.208 10 false 2 4.271,4.188 4.646,4.417 0.375,0.229 10 false GND 4.667,3.969 4.813,4.188 0.146,0.219 10 false 1 1.823,3.896 2.125,4.073 0.302,0.177 10 false A27 0.146,3 0.396,3.177 0.25,0.177 10 false E7

CAUTION / NOTICE / HINT

NOTICE:

After replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check the skid control ECU (master cylinder solenoid) connector connection.

OK:

The 2 connectors are securely connected.




OK

2.CHECK DTC

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.CHECK CAN COMMUNICATION LINE

B

3.CHECK CAN COMMUNICATION LINE
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus.

OK:

CAN Bus Check indicates no malfunctions in CAN communication.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.READ VALUE USING GTS (IG1 VOLTAGE VALUE)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.READ VALUE USING GTS (IG1 VOLTAGE VALUE)

OK

5.CHECK HARNESS AND CONNECTOR (P TERMINAL)

NG

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
5.CHECK HARNESS AND CONNECTOR (P TERMINAL)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.
U164979E02
2.583,0.49 2.51,0.49 2.51,0.49 2.427,1.135 true 0.146,0.146 0.427,0.323 0.281,0.177 10 false *a 2.646,0.417 2.813,0.594 0.167,0.177 10 false P 0.188,0.74 0.469,0.906 0.281,0.167 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-14 (P) - Body ground Ignition switch ON
w/ Rear Differential Lock: Rear differential free
11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

6.PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT)

NG

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU P CIRCUIT)
6.PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.


f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light/ ON or OFF ON: Warning light on
OFF: Warning light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

OK

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
a.

Turn the ignition switch off.


b.
U156048E03
0.635,1.438 0.448,2.208 false 0.99,1.688 1.229,2.167 false 1.865,4.021 2.302,4.021 false 0.135,0.125 0.375,0.333 0.24,0.208 10 false *a 0.25,2.24 0.656,2.469 0.406,0.229 10 false GND1 1.094,2.219 1.5,2.448 0.406,0.229 10 false GND2 2.385,3.938 2.833,4.115 0.448,0.177 10 false GND3 0.125,0.927 0.458,1.125 0.333,0.198 10 false A24 0.771,3.75 1.094,3.917 0.323,0.167 10 false A25

Disconnect the A24 and A25 skid control ECU (master cylinder solenoid) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (GND1) - Body ground Always Below 1 Ω
A24-32 (GND2) - Body ground Always Below 1 Ω
A25-4 (GND3) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU P CIRCUIT)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A27 4 wheel drive control ECU connector.


c.

w/ Rear Differential Lock:

Disconnect the f2 rear differential lock detection switch (No. 1 transfer indicator switch) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-14 (P) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (w/o Rear Differential Lock) A
OK (w/ Rear Differential Lock) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (P TERMINAL)

B

11.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (NO. 1 TRANSFER INDICATOR SWITCH)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (P TERMINAL)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.

Connect the A27 4 wheel drive control ECU connector.


c.
U164979E02
2.583,0.49 2.51,0.49 2.51,0.49 2.427,1.135 true 0.146,0.146 0.427,0.323 0.281,0.177 10 false *a 2.646,0.417 2.813,0.594 0.167,0.177 10 false P 0.188,0.74 0.469,0.906 0.281,0.167 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-14 (P) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

C

11.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (NO. 1 TRANSFER INDICATOR SWITCH)
a.

Remove the rear differential lock detection switch (No. 1 transfer indicator switch) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL).


b.

Inspect the rear differential lock detection switch (No. 1 transfer indicator switch) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION).



OK

12.CHECK HARNESS AND CONNECTOR (P TERMINAL)

NG

12.CHECK HARNESS AND CONNECTOR (P TERMINAL)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.

Connect the A27 4 wheel drive control ECU connector.


c.
U164979E02
2.583,0.49 2.51,0.49 2.51,0.49 2.427,1.135 true 0.146,0.146 0.427,0.323 0.281,0.177 10 false *a 2.646,0.417 2.813,0.594 0.167,0.177 10 false P 0.188,0.74 0.469,0.906 0.281,0.167 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-14 (P) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

C