DTC output mode is set by connecting terminals TC and CG of the DLC3.
The DTCs are output by the blinking of the ABS warning light.
When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E22-13 (TC) - E22-4 (CG) | Ignition switch ON | 11 to 14 V |
| *1 | DLC3 |
OK
NG
A
B
C
D
E
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and the GTS on.
for LHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for LHD (without Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (without Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result | Proceed to |
|---|---|
| CAN system DTC is not output | A |
| CAN system DTC is output (for LHD (with Central Gateway ECU)) | B |
| CAN system DTC is output (for LHD (without Central Gateway ECU)) | C |
| CAN system DTC is output (for RHD (with Central Gateway ECU)) | D |
| CAN system DTC is output (for RHD (without Central Gateway ECU)) | E |
A
B
C
D
E
Turn the ignition switch off.
for LHD:
Disconnect the A38 ECM connector.
for RHD:
Disconnect the A52 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-16 (TC) - E22-13 (TC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-27 (TC) - E22-13 (TC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-16 (TC) - E22-13 (TC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-27 (TC) - E22-13 (TC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-43 (TC) - E22-13 (TC) | Always | Below 1 Ω |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E22-4 (CG) - Body ground | Always | Below 1 Ω |
| *1 | DLC3 |
OK
NG
Using SST, connect terminals TC and CG of the DLC3.
Check that the MIL is blinking.
| Result | Proceed to |
|---|---|
| MIL is blinking | A |
| MIL is not blinking | B |
| *1 | DLC3 |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and the GTS on.
for LHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for LHD (without Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (with Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
for RHD (without Central Gateway ECU):
Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result | Proceed to |
|---|---|
| CAN system DTC is not output (for LHD) | A |
| CAN system DTC is not output (for RHD) | B |
| CAN system DTC is output | C |
For the CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:
for LHD (with Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD (without Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (with Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD (without Central Gateway ECU): See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
A
B
C