If any of the following is detected, the ABS warning light remains on.
The skid control ECU (master cylinder solenoid) connector is disconnected from the skid control ECU (master cylinder solenoid).
There is a malfunction in the skid control ECU (master cylinder solenoid) internal circuit.
There is an open in the harness between the combination meter and skid control ECU (master cylinder solenoid).
The anti-lock brake system is defective.
The voltage at terminal IG1 is high.
The rear differential is locked.*
*: w/ Rear Differential Lock
It may not be possible to use the GTS when the skid control ECU (master cylinder solenoid) is abnormal.
After replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).
Check the skid control ECU (master cylinder solenoid) connector connection.
The 2 connectors are securely connected.
OK
NG
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus.
CAN Bus Check indicates no malfunctions in CAN communication.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD (with Central Gateway ECU)) | B |
| NG (for LHD (without Central Gateway ECU)) | C |
| NG (for RHD (with Central Gateway ECU)) | D |
| NG (for RHD (without Central Gateway ECU)) | E |
A
B
C
D
E
OK
NG
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A24-14 (P) - Body ground | Ignition switch ON
w/ Rear Differential Lock: Rear differential free |
11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Observe the combination meter. |
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light/ ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Result | Proceed to | |
|---|---|---|
| Data List Display | Data List Display when Performing Active Test ON/OFF Operation | |
| ON | Changes between ON and OFF | A |
| Does not change between ON and OFF (for LHD) | B | |
| Does not change between ON and OFF (for RHD) | C | |
| OFF | Changes between ON and OFF | A |
| Does not change between ON and OFF (for LHD) | B | |
| Does not change between ON and OFF (for RHD) | C | |
A
(See pageVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
OK
NG
Turn the ignition switch off.
Disconnect the A24 and A25 skid control ECU (master cylinder solenoid) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-1 (GND1) - Body ground | Always | Below 1 Ω |
| A24-32 (GND2) - Body ground | Always | Below 1 Ω |
| A25-4 (GND3) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Disconnect the A27 4 wheel drive control ECU connector.
w/ Rear Differential Lock:
Disconnect the f2 rear differential lock detection switch (No. 1 transfer indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-14 (P) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/o Rear Differential Lock) | A |
| OK (w/ Rear Differential Lock) | B |
| NG | C |
A
B
C
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Connect the A27 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A24-14 (P) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
| Result | Proceed to |
|---|---|
| NG (for LHD) | A |
| NG (for RHD) | B |
| OK (for LHD) | C |
| OK (for RHD) | D |
A
B
C
D
Remove the rear differential lock detection switch (No. 1 transfer indicator switch) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL).
Inspect the rear differential lock detection switch (No. 1 transfer indicator switch) (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION).
OK
NG
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Connect the A27 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A24-14 (P) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
| Result | Proceed to |
|---|---|
| NG (for LHD) | A |
| NG (for RHD) | B |
| OK (for LHD) | C |
| OK (for RHD) | D |
A
B
C
D