Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


vi.

Read the DTCs by following the prompts on the GTS screen.



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


vi.

Operate the GTS to clear the codes.

HINT:

Refer to the GTS operator's manual for further details.





DTC CHECK/CLEAR (When Using SST Check Wire)


a.

Check for DTCs.

i.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs output from the ABS warning light in the combination meter.

HINT:
·

When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

·

When only 1 DTC is stored, the light outputs the same code after an interval of 4 seconds. Example: When DTC 21 is stored, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

·

When 2 or more DTCs are stored, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.

·

If no code is output, inspect the TC and CG terminal circuit and the ABS warning light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)



iv.

The codes are explained in the code table.

ABS DTC
ABS Warning Light Display GTS Display
11 C146E
12 C146F
21 C1468
22 C1469
23 C146A
24 C146B
25 C1225
26 C1226
27 C1227
28 C1228
31 C1401
C1405
C1409
32 C1402
C1406
C1410
33 C1403
C1407
C1411
34 C1404
C1408
C1412
35 C1413
36 C1414
37 C1337
38 C1415
39 C1416
41 C1241
C1417
42 C1242
43 C1243
44 C1418
45 C1245
46 C1421
C1422
C1423
C1424
49 C1425
51 C1251
52 C1252
53 C1253
54 C1254
56 C1256
C1452
57 C1257
58 C1453
C1454
68 C1268
94 U0073
97 C1381
98 C1336
A1* U0114

*: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.



v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.



b.

Clear the DTCs.

i.
U115769E01
0.108,0.087 0.413,0.237 0.304,0.151 10 *a 2.137,0.207 2.441,0.358 0.304,0.151 10 CG 2.205,1.943 2.510,2.094 0.304,0.151 10 TC 1.84,1.465 2.039,2.009 2.039,2.009 2.172,2.009 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).


v.

Remove SST from the terminals of the DLC3.




END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light go off within approximately 3 seconds.