Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1381  Acceleration Sensor Power Supply Voltage Malfunction  C1418  Open or Short in Acceleration Sensor Circuit  


DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the deceleration sensor. If the sensor functions abnormally, the ABS warning light turns on.

DTC Code DTC Detection Condition Trouble Area
C1243 The following condition repeats 16 times.
·

Sensor signal do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).


·

Deceleration sensor

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)


C1245 The following condition continues for at least 60 seconds.
·

The difference between the values calculated from the deceleration sensor value and vehicle speed exceeds 0.35 G.


C1381 At a vehicle speed of more than 3 km/h (2 mph), the deceleration sensor power source malfunction signal is received for 10 seconds or more.
C1418 One of the following conditions is met when the voltage at terminal IG1 is 9.5 V or higher:
·

The power supply voltage of the deceleration sensor is outside the range of 4.4 to 5.6 V for 1.2 seconds or more.

·

The value of GL1 is outside the range of -1.5 to 1.5 G for 1.2 seconds or more.

·

A deceleration sensor open circuit occurs 7 times or more.


C1279 Stored during test mode.

WIRING DIAGRAM

C177519E07
0.896,1.417 1.333,1.635 0.438,0.219 10 false GGND 1.031,0.99 1.323,1.219 0.292,0.229 10 false GL1 0.99,0.625 1.323,0.823 0.333,0.198 10 false VGS 5.917,1.406 6.375,1.604 0.458,0.198 10 false GGND 5.917,1.021 6.271,1.24 0.354,0.219 10 false GL1 5.917,0.635 6.26,0.875 0.344,0.24 10 false VGS 0.552,1.938 0.854,2.135 0.302,0.198 10 false E88 0.552,2.125 1.906,2.375 1.354,0.25 10 false Deceleration Sensor 1.438,1.292 1.625,1.49 0.188,0.198 10 false 2 1.427,0.927 1.604,1.104 0.177,0.177 10 false 1 1.427,0.521 1.583,0.677 0.156,0.156 10 false 3 5.646,1.313 5.854,1.479 0.208,0.167 10 false 23 5.646,0.927 5.854,1.094 0.208,0.167 10 false 39 5.646,0.542 5.854,0.708 0.208,0.167 10 false 22 5.438,1.75 5.781,1.938 0.344,0.188 10 false A24 5.438,1.99 7.125,2.417 1.688,0.427 10 false Skid Control ECU (Master Cylinder Solenoid)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the deceleration sensor, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK DECELERATION SENSOR INSTALLATION
a.

Check that the deceleration sensor is installed properly.

Result
Result Proceed to
The sensor is tightened to the specified torque.
The sensor is not tilted.
A
The sensor is not tightened to the specified torque.
Or the sensor is tilted.
B



A

2.READ VALUE USING GTS (DECELERATION SENSOR)

B

2.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Deceleration Sensor Deceleration sensor reading / min.: -18.525 m/s2, max.: 18.387 m/s2 Approximately -1.28 to 1.27 m/s2 while stationary The reading changes when the vehicle is bounced.


f.

Check the Data List for proper functioning of the deceleration sensor.

OK:

Deceleration value changes.




OK

3.CHECK DTC

NG

4.INSPECT DECELERATION SENSOR
3.CHECK DTC
a.

Install the deceleration sensor to the vehicle.



c.

Turn the ignition switch off.


d.

Drive the vehicle at 6 km/h (4 mph) or more.


e.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.INSPECT DECELERATION SENSOR

C261972E02
2.292,0.948 2.25,0.438 2.25,0.438 2.073,0.438 true 1.479,1 1.479,0.948 1.479,0.948 2.125,0.948 true 2.531,0.948 3.135,0.948 3.135,0.948 3.135,1.021 true 1.396,0.354 2.083,0.552 0.688,0.198 10 false 2 (GGND) 2.906,1.063 3.406,1.271 0.5,0.208 10 false 1 (GL1) 1.229,1.063 1.792,1.281 0.563,0.219 10 false 3 (VGS) 2.667,0.313 2.906,0.49 0.24,0.177 10 false *a 2.417,2.458 2.667,2.677 0.25,0.219 10 false *b 2.677,3.104 2.927,3.323 0.25,0.219 10 false *c 0.365,4.135 0.615,4.354 0.25,0.219 10 false *d

b.

Connect 3 dry cell batteries of 1.5 V in series.

NOTICE:

Do not apply 6 V or more to terminals 3 (VGS) and 2 (GGND).



c.

Check the output voltage of terminal 1 (GL1) when the sensor is tilted forward and rearward.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (GL1) - Battery negative (-) lead Horizontal Approximately 2.5 V
Tilted forward Approximately 0.5 to 2.5 V
Tilted rearward Approximately 2.5 to 4.5 V


Text in Illustration
*a Component without harness connected
(Deceleration Sensor)
*b Front
*c Tilted forward
*d Tilted rearward

HINT:
·

If the sensor is tilted too much, it may output the wrong value.

·

If the voltage drops, the sensor should be replaced with a new one.

·

When replacing the sensor, it should not be placed upside down.





OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DECELERATION SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DECELERATION SENSOR)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the E88 deceleration sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-39 (GL1) - E88-1 (GL1) Always Below 1 Ω
A24-23 (GGND) - E88-2 (GGND) Always Below 1 Ω
A24-22 (VGS) - E88-3 (VGS) Always Below 1 Ω
E88-1 (GL1) - Body ground Always 10 kΩ or higher
E88-2 (GGND) - Body ground Always 10 kΩ or higher
E88-3 (VGS) - Body ground Always 10 kΩ or higher




OK

6.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DTC
a.

Install the deceleration sensor to the vehicle.



c.

Turn the ignition switch off.


d.

Drive the vehicle at 6 km/h (4 mph) or more.


e.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C