Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If the voltage supplied to the IG1 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1241 Either condition is met:
1. Both of the following conditions continue for at least 10 seconds.
·

The vehicle speed is more than 3 km/h (2 mph).

·

The IG1 terminal voltage is below 9.5 V.


2. All of the following conditions continue for at least 0.2 seconds.
·

The solenoid relay remains on.

·

The IG1 terminal voltage is below 9.5 V.

·

The relay contact is open.


·

Battery

·

ECU-IG No. 2 fuse

·

Charging system

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173289E22
3.438,1.073 4.688,1.25 1.25,0.177 10 false ECU-IG No. 2 0.406,0.917 1.427,1.094 1.021,0.177 10 false from IG Circuit 5.51,4.74 7.146,5.146 1.635,0.406 10 false Skid Control ECU (Master Cylinder Solenoid) 6.146,3.313 6.594,3.49 0.448,0.177 10 false GND3 5.833,3.083 5.979,3.26 0.146,0.177 10 false 4 6.125,2.521 6.573,2.698 0.448,0.177 10 false GND2 5.792,2.333 6.01,2.51 0.219,0.177 10 false 32 6.135,1.74 6.583,1.917 0.448,0.177 10 false GND1 5.833,1.521 5.979,1.698 0.146,0.177 10 false 1 6.135,0.906 6.385,1.083 0.25,0.177 10 false IG1 5.729,0.927 6.063,1.083 0.333,0.156 10 false A24 5.74,1.74 6.063,1.927 0.323,0.188 10 false A24 5.729,2.521 6.063,2.688 0.333,0.167 10 false A24 5.74,3.302 6.052,3.479 0.313,0.177 10 false A25 5.792,0.729 6.021,0.906 0.229,0.177 10 false 46

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (IG1 VOLTAGE VALUE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG1 Voltage Value IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11 to 14 V -


g.

Check the voltage output from the skid control ECU (master cylinder solenoid) displayed on the GTS.

OK:

The output voltage displayed on the GTS is within 11 to 14 V.




OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output (for LHD) A
DTC is output (for RHD) B
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) C
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) D



A

B

C

D

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Disconnect the skid control ECU (master cylinder solenoid) connector.


b.
U156218E03
2.646,1.552 2.646,1.854 false 0.125,0.073 0.406,0.385 0.281,0.313 10 false *a 2.563,1.885 2.844,2.063 0.281,0.177 10 false IG1 0.24,0.708 0.51,0.875 0.271,0.167 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-46 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))



OK

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output (for LHD) A
DTC is output (for RHD) B
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart) C
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table) D



A

B

C

D

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE