Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255416 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1242  Open Circuit in IG1/IG2 Power Source Circuit  


DESCRIPTION

If there is a problem with the skid control ECU (master cylinder solenoid) power supply circuit, the skid control ECU (master cylinder solenoid) stores DTCs and prohibits operation under the fail-safe function.

If the voltage supplied to the IG2 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1242 The vehicle speed is 3 km/h (2 mph) or more and the voltage at the ECU IG2 terminal remains below 6.5 V for more than 7 seconds.
·

Battery

·

IGN fuse

·

Charging system

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173290E18
0.385,0.927 1.385,1.135 1,0.208 10 false from IG Circuit 5.51,4.74 7.125,5.146 1.615,0.406 10 false Skid Control ECU (Master Cylinder Solenoid) 6.135,3.302 6.583,3.479 0.448,0.177 10 false GND3 5.833,3.115 5.979,3.292 0.146,0.177 10 false 4 6.135,2.531 6.583,2.708 0.448,0.177 10 false GND2 5.802,2.333 6.021,2.51 0.219,0.177 10 false 32 6.125,1.75 6.573,1.927 0.448,0.177 10 false GND1 5.74,1.729 6.063,1.906 0.323,0.177 10 false A24 5.75,2.521 6.063,2.698 0.313,0.177 10 false A24 5.833,1.521 5.979,1.698 0.146,0.177 10 false 1 6.146,0.906 6.417,1.083 0.271,0.177 10 false IG2 5.74,0.927 6.094,1.104 0.354,0.177 10 false A25 5.74,3.313 6.042,3.49 0.302,0.177 10 false A25 5.823,0.708 5.99,0.885 0.167,0.177 10 false 1 3.708,1.083 4.063,1.26 0.354,0.177 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the master cylinder solenoid, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
C358306E01
0.646,0.552 1.021,0.802 0.375,0.25 1.167,1.229 1.573,0.896 false 0.708,0.594 1.021,0.792 0.313,0.198 10 false A25 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 0.854,1.24 1.167,1.438 0.313,0.198 10 false IG2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A25-1 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C