Home › Steering › VARIABLE GEAR RATIO STEERING › STEERING ACTUATOR › from 2015.08
RM2660E _55 Steering _052825 VARIABLE GEAR RATIO STEERING _0255449 STEERING ACTUATOR A

VARIABLE GEAR RATIO STEERING  STEERING ACTUATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. HANDLING PRECAUTIONS FOR STEERING ACTUATOR ASSEMBLY

NOTICE:
·

Be careful that the No. 2 seal lip or boot does not turn outward while carrying or installing the steering actuator assembly. If installing a new steering actuator assembly, make sure that the spiral center lock pin is securely inserted.

·

Do not use the steering actuator assembly if it has been dropped.

C179309E05
1.563,0.177 2.188,0.177 2.188,0.177 2.417,0.354 false 2.875,1.833 2.875,2.177 false 2.875,2.177 3.25,2.177 false 3.896,0.094 3.469,0.094 false 3.469,0.094 3.417,0.323 false 4.677,0.729 5.073,0.323 false 5.073,0.323 5.573,0.323 false 0.781,0.094 1.563,0.292 0.781,0.198 10 false Spiral Case 3.313,2.083 5.594,2.281 2.281,0.198 10 false Actuator Clamp (Not tighten at first) 3.979,0.042 4.375,0.24 0.396,0.198 10 false Boot 5.635,0.25 6.573,0.438 0.938,0.188 10 false No. 2 Seal Lip



Hide 45240J 2.INSTALL STEERING ACTUATOR ASSEMBLY

a.

Make sure that the power steering link assembly is centered.


b.
C179311E03
1.292,2.625 2.375,2.625 false 1.458,3.042 1.229,3.042 false 1.229,3.042 1.073,3 false 2.427,2.552 3.208,2.708 0.781,0.156 10 false White Line 1.51,2.938 2.573,3.104 1.063,0.167 10 false Center Lock Pin

Install the steering actuator assembly.

i.

If installing a new steering actuator assembly:

Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.

NOTICE:

Do not pull out the center lock pin.



ii.
C179313E04
0.615,1.771 0.271,3.052 false 0.271,3.052 0.563,3.052 false 1.333,2.531 2.177,2.708 false 2.177,2.708 2.333,2.708 false 1,1.781 0.635,0.521 false 0.635,0.521 0.49,0.521 false 1.646,0.198 1.313,0.198 false 1.313,0.198 1.104,1.531 false 0.635,2.948 1.667,3.115 1.031,0.167 10 false Alignment Mark 2.375,2.615 3.188,2.781 0.813,0.167 10 false White Line 0.177,0.406 0.49,0.604 0.313,0.198 10 false Slit 1.708,0.094 2.521,0.281 0.813,0.188 10 false Sliding Yoke

If reinstalling the removed steering actuator assembly:

1.

Slowly turn the spiral case clockwise until it locks.

2.

Turn the spiral case two turns counterclockwise from the lock position.

3.

Align the slit of the sliding yoke with the alignment mark (▲).

4.

Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.




c.
C172649E06
1.875,0.854 2.396,0.563 false 1.625,1.104 2.396,0.563 false 2.479,0.469 3.344,0.729 0.865,0.26 10 true Matchmark

Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.

NOTICE:
·

Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.

·

Do not turn the actuator body and the spiral case.



HINT:

Install the steering actuator from the inside of the vehicle.



d.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


e.
C180144

Using needle nose pliers, lock the clamp to the steering column hole cover to install it.

NOTICE:

Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.



f.
C179338

Move the lock in the direction of the arrow and connect the steering actuator connector.

HINT:

When a new actuator is installed, remove the center lock pin.



g.

Connect the connector.


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
·

Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 6. PERFORM VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION