Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The steering lock ECU activates the steering lock motor by the power from the main body ECU through the IGE circuit. This prevents the steering from being locked while the vehicle is moving.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

DTC Code Detection Condition Trouble Area
B2782 IGE power supply circuit malfunction
·

Steering lock actuator assembly (steering lock ECU)

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

C165587E11
1.396,1.323 1.792,1.51 0.396,0.188 10 false SLR+ 1.885,1.448 2.115,1.635 0.229,0.188 10 false 19 0.688,2.896 1.021,3.083 0.333,0.188 10 false E1 3.792,2.927 4.125,3.115 0.333,0.188 10 false E26 4.188,1.354 4.583,1.542 0.396,0.188 10 false IGE 3.948,1.438 4.094,1.625 0.146,0.188 10 false 3 4.188,2.333 4.583,2.521 0.396,0.188 10 false GND 5.104,1.823 6.51,2.01 1.406,0.188 10 false Steering Lock Motor 3.948,2.427 4.094,2.615 0.146,0.188 10 false 1 0.677,3.104 2.24,3.552 1.563,0.448 10 false Main Body ECU (Cowl Side Junction Block LH) 3.771,3.135 6,3.479 2.229,0.344 10 false Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.CHECK DTC OUTPUT (B2785)
a.

Check for DTCs (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2782 is output, but DTC B2785 is not output.




OK

2.INSPECT STEERING LOCK ECU

NG

GO TO LIN COMMUNICATION SYSTEM (B2785)

2.INSPECT STEERING LOCK ECU
U164601E02
2.594,2.813 2.479,2.813 2.479,2.813 2.24,2.052 true 1.521,2.813 1.625,2.813 1.625,2.813 1.875,2.052 true 0.396,0.198 2.74,0.563 2.344,0.365 10 false Component with harness connected: (Steering Lock ECU) 2.667,2.729 3.167,2.927 0.5,0.198 10 false GND 1.24,2.729 1.563,2.927 0.323,0.198 10 false IGE 0.25,1.906 0.625,2.135 0.375,0.229 10 false E26

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-3 (IGE) - E26-1 (GND)
·

Engine switch on (IG)

·

Steering lock motor is operating


Below 1 V
E26-3 (IGE) - E26-1 (GND)
·

Engine switch on (IG)

·

Steering lock motor is not operating


11 to 14 V


Result
Result Proceed to
Within specified range (for Power tilt and telescopic) A
Outside specified range B
Within specified range (for Manual tilt and telescopic) C

HINT:

When the steering lock is activated and the engine switch is turned on (IG), the steering lock motor activates to release the steering lock. The motor operation occurs for 2 to 15 seconds.




A

B

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU AND BODY GROUND)

C

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU AND BODY GROUND)
U164594E02
4.198,2.49 4.281,2.49 4.281,2.49 5.052,1.823 true 4.188,2.219 4.271,2.219 4.271,2.219 4.719,1.833 true 0.958,2.323 1.052,2.323 1.052,2.323 1.385,2.042 true 1.677,0.927 2.052,1.156 0.375,0.229 10 false E1 5.094,0.927 5.469,1.156 0.375,0.229 10 false E26 0.49,0.063 2.896,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 3.979,0.063 6.385,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 0.552,2.24 0.969,2.438 0.417,0.198 10 false SLR+ 3.896,2.417 4.208,2.615 0.313,0.198 10 false IGE 3.844,2.125 4.198,2.323 0.354,0.198 10 false GND

a.

Disconnect the E26 steering lock ECU connector.


b.

Disconnect the E1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-3 (IGE) - E1-19 (SLR+) Always Below 1 Ω
E26-1 (GND) - Body ground Always Below 1 Ω
E26-3 (IGE) or E1-19 (SLR+) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR