Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

Unlock Request Receive

·

S Code Check

·

L Code Check


-

WIRING DIAGRAM

C331936E09
3.333,0.75 4.229,0.927 0.896,0.177 10 false STRG LOCK 1.375,0.573 2.208,0.792 0.833,0.219 10 false from Battery 5.167,0.573 5.323,0.771 0.156,0.198 10 false B 4.948,0.458 5.104,0.656 0.156,0.198 10 false 7 5.042,5.594 6.823,5.958 1.781,0.365 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 5.052,5.417 5.51,5.615 0.458,0.198 10 false E26 5.146,4.729 5.604,4.927 0.458,0.198 10 false GND 5.135,4.094 5.75,4.292 0.615,0.198 10 false SLP1 5.146,3.667 5.604,3.865 0.458,0.198 10 false IGE 5.146,3.188 5.604,3.385 0.458,0.198 10 false LIN 1.396,4.094 1.854,4.292 0.458,0.198 10 false SLP 1.313,3.656 1.927,3.854 0.615,0.198 10 false SLR+ 1.448,3.167 1.906,3.365 0.458,0.198 10 false LIN 1.76,3.552 2.073,3.75 0.313,0.198 10 false 24 1.76,4.625 2.073,4.823 0.313,0.198 10 false 11 1.552,4.729 1.708,4.927 0.156,0.198 10 false E 1.76,4.083 2.073,4.281 0.313,0.198 10 false 23 1.771,2.99 1.927,3.188 0.156,0.198 10 false 6 0.656,4.083 0.969,4.281 0.313,0.198 10 false IC 0.948,3.521 1.26,3.719 0.313,0.198 10 false +B 0.281,5.375 0.74,5.573 0.458,0.198 10 false E130 0.281,5.531 1.802,5.948 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.646,6.281 2.25,6.49 1.604,0.208 10 false : LIN Communication Line 4.938,4.615 5.094,4.813 0.156,0.198 10 false 1 4.938,4.073 5.094,4.271 0.156,0.198 10 false 4 4.927,3.552 5.083,3.75 0.156,0.198 10 false 3 4.927,2.958 5.083,3.156 0.156,0.198 10 false 5 0.156,2.01 1.781,2.365 1.625,0.354 10 false ID Code Box (Immobiliser Code ECU) 0.156,1.844 0.615,2.042 0.458,0.198 10 false E124 1.25,1.385 1.865,1.583 0.615,0.198 10 false LIN1 1.667,1.188 1.823,1.385 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, confirm that the problem does not occur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

When starting the engine, make sure that the shift lever is in P and that the shift lever is not tilted.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → on (ACC) → on (IG) → off





OK

2.CHECK INDICATOR

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

2.CHECK INDICATOR
a.

With the engine switch on (IG), check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.

Result
Result Proceed to
Steering Lock active is displayed. A
Steering Lock active is not displayed. B



A

3.CHECK STEERING UNLOCK

B

4.CHECK FOR DTC
3.CHECK STEERING UNLOCK
a.

While turning the steering wheel left and right, press the engine switch.


b.

Check that the steering is unlocked.

Result
Result Proceed to
The steering is unlocked. A
The steering is not unlocked. B



A

END

B

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Using the GTS, check if the certification ECU (smart key ECU assembly) DTC is output.

Result
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock request is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".




OK

6.READ VALUE USING GTS (S CODE CHECK)

NG

11.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
6.READ VALUE USING GTS (S CODE CHECK)

OK

7.READ VALUE USING GTS (L CODE CHECK)

NG

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.READ VALUE USING GTS (L CODE CHECK)

OK

8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

15.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.
U156087E01
1.146,1.979 0.719,2.781 false 2.323,1.958 2.729,2.771 false 0.229,0.365 2.573,0.719 2.344,0.354 10 false *a 1.635,0.948 1.917,1.125 0.281,0.177 10 false E26 0.677,2.813 1.104,2.99 0.427,0.177 10 false B 2.594,2.781 3.031,2.958 0.438,0.177 10 false GND

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
E26-7 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))



OK

9.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Disconnect the steering lock ECU (steering lock actuator assembly) connector.


b.
U156090E01
0.377,0.3 0.605,0.476 0.227,0.176 10 *a 0.429,0.986 0.738,1.128 0.309,0.142 10 E26 0.818,1.558 1.176,1.742 0.357,0.184 10 GND 1.281,2.42 1.032,1.733 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))



OK

10.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the E26 steering lock ECU (steering lock actuator assembly) connector.


b.
U156265E03
2.26,1.125 2.677,1.76 true 1.438,2.917 2.792,2.698 2.792,2.698 2.625,2.969 false 2.052,4.219 2.052,4.406 false 1.906,1.104 0.75,1.74 true 0.292,0.125 0.469,0.313 0.177,0.188 10 false *a 2.833,2.594 3.01,2.781 0.177,0.188 10 false *b 2,4.417 2.177,4.604 0.177,0.188 10 false *c 0.26,0.823 0.573,0.99 0.313,0.167 10 false E26 0.615,1.75 0.896,1.917 0.281,0.167 10 false IGE 2.583,1.771 2.938,1.938 0.354,0.167 10 false GND 2.979,4.063 3.354,4.229 0.375,0.167 10 false GND

Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection E26-3 (IGE) - E26-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.




Result
Result Proceed to
OK for Manual Tilt and Manual Telescopic Steering Column A
for Power Tilt and Power Telescopic Steering Column B
NG C


A

B

C

16.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
11.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.
U156088E01
1.76,1.958 2.49,2.823 true 0.375,0.271 0.635,0.479 0.26,0.208 10 false *a 0.323,0.958 0.667,1.115 0.344,0.156 10 false E26 2.385,2.854 2.917,3.01 0.531,0.156 10 false SLP1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-4 (SLP1) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))



OK

12.READ VALUE USING GTS (STEERING UNLOCK)

NG

18.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
12.READ VALUE USING GTS (STEERING UNLOCK)
a.

Check that the steering is locked.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Steering lock ECU (steering lock actuator assembly) unlock confirmation status / Unset or Set Unset: Unlock not confirmed
Set: Unlock confirmed
When Unset is displayed, the steering is not unlocked (the engine cannot be started).

OK:

"Set" is displayed on the GTS.


Result
Result Proceed to
OK A
NG for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

13.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

B

C

13.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock request is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Unlock Request Receive Unlock request signal received state / OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of a engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

15.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

16.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

OK

17.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


b.

Reconnect the certification ECU (smart key ECU assembly) connector.


c.
U156086E01
1.906,1.958 2.479,2.823 true 0.281,0.271 0.542,0.479 0.26,0.208 10 false *a 0.333,0.969 0.677,1.125 0.344,0.156 10 false E26 2.438,2.854 2.813,3.01 0.375,0.156 10 false IGE

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-3 (IGE) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))

Result
Result Proceed to
OK A
NG for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

18.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the steering lock ECU (steering lock actuator assembly) connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-4 (SLP1) - E130-23 (SLP) Always Below 1 Ω
E26-4 (SLP1) or E130-23 (SLP) - Body ground Always 10 kΩ or higher




OK

19.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock request is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Unlock Request Receive Unlock request signal received state / OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of a engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".




OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)