Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock does not Lock  


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to lock steering wheel
Entry&Start
·

Lock Request Receive

·

S Code Check

·

L Code Check


Main Body
·

FL Door Courtesy SW

·

FR Door Courtesy SW


Power Source Control
·

Shift P Signal


-

WIRING DIAGRAM

C339126E04
2.844,6.385 3.302,6.594 0.458,0.208 10 false E130 2.844,6.552 4.448,6.958 1.604,0.406 10 false Certification ECU (Smart Key ECU Assembly) 5.219,6.365 5.708,6.563 0.49,0.198 10 false E26 5.229,6.542 7.104,6.927 1.875,0.385 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.708,7.052 2.625,7.281 1.917,0.229 10 false : LIN Communication Line 0.708,7.365 2.625,7.594 1.917,0.229 10 false : CAN Communication Line 0.75,5.698 1.25,5.854 0.5,0.156 10 false E 1.792,5.688 2.292,5.844 0.5,0.156 10 false P2 0.615,6.073 1.052,6.25 0.438,0.177 10 false E51 0.604,6.25 2.146,6.438 1.542,0.188 10 false Shift Lock Control ECU 0.365,1.833 0.865,1.99 0.5,0.156 10 false E124 1.719,1.313 2.219,1.469 0.5,0.156 10 false LIN1 2.406,0.688 3.635,0.917 1.229,0.229 10 false from Battery 3.927,0.865 4.792,1.021 0.865,0.156 10 false STRG LOCK 5.677,3.385 6.323,3.542 0.646,0.156 10 false LIN 3.708,3.406 4.354,3.563 0.646,0.156 10 false LIN 4.021,3.219 4.667,3.375 0.646,0.156 10 false 6 3.573,4.354 4.219,4.51 0.646,0.156 10 false SLR+ 4.031,4.24 4.656,4.448 0.625,0.208 10 false 24 5.469,3.229 5.625,3.385 0.156,0.156 10 false 5 5.656,0.708 6.302,0.865 0.646,0.156 10 false B 5.448,0.573 5.604,0.729 0.156,0.156 10 false 7 5.667,4.323 6.313,4.479 0.646,0.156 10 false IGE 5.458,4.229 5.615,4.385 0.156,0.156 10 false 3 5.656,5.74 6.302,5.896 0.646,0.156 10 false GND 5.469,5.615 5.625,5.771 0.156,0.156 10 false 1 2.115,1.135 2.615,1.292 0.5,0.156 10 false 2 0.365,2.021 1.99,2.385 1.625,0.365 10 false ID Code Box (Immobiliser Code ECU) 0.406,4.427 2.104,4.802 1.698,0.375 10 false Main Body ECU (Multiplex Network Body ECU 2.042,5.573 2.292,5.76 0.25,0.188 10 false 11 2.938,5.563 3.188,5.719 0.25,0.156 10 false 22 3.198,5.667 3.448,5.823 0.25,0.156 10 false P 0.583,5.573 1.083,5.729 0.5,0.156 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).

·

After performing repairs, confirm that the problem does not occur.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock command is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK: Within 10 seconds of opening any door with engine switch off and shift lever in P
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.




OK

2.READ VALUE USING GTS (S CODE CHECK)

NG

6.READ VALUE USING GTS (DOOR COURTESY SW)
2.READ VALUE USING GTS (S CODE CHECK)
a.

Use the Data List to check if S code certification is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.





OK

3.READ VALUE USING GTS (L CODE CHECK)

NG

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
3.READ VALUE USING GTS (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.





OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

11.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the steering lock ECU (steering lock actuator assembly) connector.


c.
U164541E01
0.377,0.3 0.605,0.476 0.227,0.176 10 *a 0.429,0.986 0.738,1.128 0.309,0.142 10 E26 0.818,1.558 1.176,1.742 0.357,0.184 10 GND 1.281,2.42 1.032,1.733 false 2.428,1.554 2.785,1.738 0.357,0.184 10 B 2.255,2.416 2.469,1.73 false

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
E26-7 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))



OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


b.

Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.


c.
U156264E03
2.281,1.104 2.698,1.74 true 1.427,2.906 2.792,2.698 2.792,2.698 2.615,2.958 false 2.042,4.219 2.042,4.406 false 1.896,1.115 0.74,1.75 true 0.354,0.115 0.531,0.302 0.177,0.188 10 false *a 2.833,2.583 3.01,2.771 0.177,0.188 10 false *b 1.969,4.417 2.146,4.604 0.177,0.188 10 false *c 0.26,0.823 0.573,0.99 0.313,0.167 10 false E26 0.542,1.76 0.833,1.927 0.292,0.167 10 false IGE 2.583,1.771 2.938,1.938 0.354,0.167 10 false GND 2.979,4.063 3.354,4.229 0.375,0.167 10 false GND

Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection E26-3 (IGE) - E26-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating

HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.




Result
Result Proceed to
OK for Manual Tilt and Manual Telescopic Steering Column A
for Power Tilt and Power Telescopic Steering Column B
NG C



A

B

C

12.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Using the GTS, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH / ON or OFF OFF: Front door LH closed
ON: Front door LH open
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part.

OK:

The Data List item changes in accordance with the opening and closing of the driver door.




OK

7.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY LIGHT CIRCUIT)

7.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal / ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.

OK:

ON is displayed on the GTS.




OK

8.READ VALUE USING GTS (STEERING LOCK)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

8.READ VALUE USING GTS (STEERING LOCK)
a.

Check that the steering is unlocked.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Lock Steering lock ECU (steering lock actuator assembly) unlock confirmation status / Unset or Set Unset: Unlock not confirmed
Set: Unlock confirmed
When Unset is displayed, the steering is not unlocked (the engine cannot be started).

OK:

Set is displayed on the GTS.


Result
Result Proceed to
OK A
NG for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



OK

9.READ VALUE USING GTS (LOCK REQUEST RECEIVE)

B

C

9.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock command is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Lock Request Receive Lock request signal received state / OK or NG OK: Lock request signal received for 10 seconds of any of the doors being opened with shift lever in P and engine switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the GTS screen.




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK is displayed on the GTS.




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

HINT:



b.

Perform registration (refer to Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly again.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK is displayed on the GTS.




OK

END

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

12.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

OK

13.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

13.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


b.

Reconnect the certification ECU (smart key ECU assembly) connector.


c.
U156086E01
1.906,1.958 2.479,2.823 true 0.281,0.271 0.542,0.479 0.26,0.208 10 false *a 0.333,0.969 0.677,1.125 0.344,0.156 10 false E26 2.438,2.854 2.813,3.01 0.375,0.156 10 false IGE

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E26-3 (IGE) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))

Result
Result Proceed to
OK A
NG for Manual Tilt and Manual Telescopic Steering Column B
for Power Tilt and Power Telescopic Steering Column C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C