Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255452 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unlock Position Sensor Signal Circuit  


DESCRIPTION

The steering lock ECU sends an unlock position signal to the main body ECU. On receiving the signal, the main body ECU permits an engine start. This prevents the engine from being started with the steering locked.

The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

WIRING DIAGRAM

C165587E13
1.479,1.323 1.833,1.51 0.354,0.188 10 false SLP 1.885,1.458 2.115,1.646 0.229,0.188 10 false 18 0.667,2.885 1,3.073 0.333,0.188 10 false E1 3.688,2.896 4.021,3.083 0.333,0.188 10 false E26 4.188,1.333 4.656,1.521 0.469,0.188 10 false SLP1 3.927,1.448 4.073,1.635 0.146,0.188 10 false 4 4.177,2.313 4.719,2.5 0.542,0.188 10 false SGND 5.104,1.813 6.51,2 1.406,0.188 10 false Steering Lock Motor 3.958,2.417 4.104,2.604 0.146,0.188 10 false 2 0.667,3.104 2.188,3.552 1.521,0.448 10 false Main Body ECU (Cowl Side Junction Block LH) 3.677,3.063 5.906,3.406 2.229,0.344 10 false Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:

With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.INSPECT STEERING LOCK ECU
U164605E02
2.406,2.823 2.292,2.823 2.292,2.823 2.052,2.063 true 1.354,2.802 1.469,2.802 1.469,2.802 1.708,2.042 true 0.396,0.24 2.74,0.604 2.344,0.365 10 false Component with harness connected: (Steering Lock ECU) 2.479,2.74 2.979,2.938 0.5,0.198 10 false SGND 0.958,2.719 1.333,2.917 0.375,0.198 10 false SLP1 0.25,1.906 0.625,2.135 0.375,0.229 10 false E26

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition (Steering Lock Position) Specified Condition
E26-4 (SLP1) - E26-2 (SGND) Locked 11 to 14 V
E26-4 (SLP1) - E26-2 (SGND) Unlocked Below 1 V




OK

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)
2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - MAIN BODY ECU)
U164597E02
4.302,2.323 4.396,2.323 4.396,2.323 5.188,1.813 true 0.813,2.292 0.906,2.292 0.906,2.292 1.292,2.042 true 1.688,0.917 2.063,1.146 0.375,0.229 10 false E1 5.094,0.927 5.469,1.156 0.375,0.229 10 false E26 0.604,0.156 3.01,0.521 2.406,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 4.063,0.188 6.469,0.552 2.406,0.365 10 false Front view of wire harness connector: (to Steering Lock ECU) 0.51,2.188 0.844,2.385 0.333,0.198 10 false SLP 3.906,2.229 4.281,2.427 0.375,0.198 10 false SLP1

a.

Disconnect the E26 steering lock ECU connector.


b.

Disconnect the E1 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-4 (SLP1) - E1-18 (SLP) Always Below 1 Ω
E26-4 (SLP1) or E1-18 (SLP) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
Within specified range (for Power tilt and telescopic) A
Within specified range (for Manual tilt and telescopic) B
Outside specified range C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR