Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255453 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2611  Telescopic Position Sensor or Telescopic Motor Circuit Malfunction  


DESCRIPTION

The telescopic motor is operated by voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position of the steering column in the forward and backward directions and sends a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

DTC No. Detection Item Trouble Area
B2611 Telescopic operation stops within the operation range while operating.
·

TI &TE fuse

·

Telescopic position sensor or telescopic motor

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C244373E25
2.156,0.885 2.927,1.073 0.771,0.188 10 false from Battery 3.521,1.042 4.031,1.188 0.51,0.146 10 false TI & TE 4.698,0.896 4.99,1.042 0.292,0.146 10 false +B 4.51,0.833 4.615,0.979 0.104,0.146 10 false 2 1.688,1.198 2.104,1.344 0.417,0.146 10 false TEM+ 2.135,1.99 2.25,2.135 0.115,0.146 10 false 1 1.688,1.99 2.115,2.135 0.427,0.146 10 false TEM- 2.146,1.198 2.26,1.344 0.115,0.146 10 false 2 1.76,2.76 2.24,2.906 0.479,0.146 10 false VCE 2.146,2.74 2.25,2.906 0.104,0.167 10 false 5 1.781,3.167 2.115,3.313 0.333,0.146 10 false TES 2.146,3.146 2.26,3.313 0.115,0.167 10 false 4 1.865,3.552 2.063,3.698 0.198,0.146 10 false E2 2.146,3.531 2.26,3.698 0.115,0.167 10 false 3 0.771,1.51 2,1.719 1.229,0.208 10 false Telescopic Motor 4.677,1.229 5.094,1.427 0.417,0.198 10 false TEM+ 4.667,2.021 5.042,2.219 0.375,0.198 10 false TEM- 4.677,2.781 5,2.979 0.323,0.198 10 false VCE 4.688,3.167 5.021,3.365 0.333,0.198 10 false TES 4.688,3.552 4.938,3.75 0.25,0.198 10 false E2 0.5,3.844 1.792,4.25 1.292,0.406 10 false Telescopic Position Sensor 4.438,2.031 4.625,2.229 0.188,0.198 10 false 19 4.448,2.781 4.635,2.99 0.188,0.208 10 false 14 4.448,3.167 4.76,3.375 0.313,0.208 10 false 15 4.688,4.74 5.021,4.938 0.333,0.198 10 false E144 4.51,1.229 4.75,1.427 0.24,0.198 10 false 6 4.51,3.875 4.75,4.073 0.24,0.198 10 false 8 4.448,3.563 4.76,3.76 0.313,0.198 10 false 17 4.677,3.875 5.24,4.073 0.563,0.198 10 false GND2 4.51,4.26 4.75,4.458 0.24,0.198 10 false 1 4.677,4.354 5.24,4.552 0.563,0.198 10 false GND 6.021,1.042 6.333,1.24 0.313,0.198 10 false +B 6.021,1.833 6.333,2.031 0.313,0.198 10 false +B 6.083,3.042 6.49,3.24 0.406,0.198 10 false 12 V 6.01,3.75 6.583,3.948 0.573,0.198 10 false to CPU 4.688,4.927 6.823,5.167 2.135,0.24 10 false Multiplex Tilt and Telescopic ECU 0.698,4.917 1.948,5.125 1.25,0.208 10 false Telescopic Motor 0.698,4.74 1.094,4.948 0.396,0.208 10 false E142

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TELESCO OPERATION)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Check that the steering column contracts and extends. Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Telesco Operation Telescopic operation LONG/SHORT -

OK:

The steering column contracts and extends.




OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR)
a.

Disconnect the E144 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E142 telescopic motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-6 (TEM+) - E142-2 (TEM+) Always Below 1 Ω
E144-19 (TEM-) - E142-1 (TEM-)
E144-6 (TEM+) - Body ground 10 kΩ or higher
E144-19 (TEM-) - Body ground




OK

5.CHECK TELESCOPIC MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELESCOPIC MOTOR
a.

Disconnect the E142 telescopic motor connector.


b.
U117406E01
0.305,0.226 0.508,0.414 0.204,0.188 10 *a 2.069,1.112 2.386,0.666 false 2.069,1.112 2.386,0.666 false 2.439,0.555 2.899,0.740 0.459,0.185 10 TEM- 1.358,1.131 1.042,0.686 false 1.358,1.131 1.042,0.686 false 0.548,0.587 1.035,0.772 0.487,0.185 10 TEM+

Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

OK:
Measurement Condition Specified Condition
·

12 V battery positive (+) lead → Terminal 2 (TEM+)

·

12 V battery negative (-) lead → Terminal 1 (TEM-)


The steering column contracts.
·

12 V battery positive (+) lead → Terminal 1 (TEM-)

·

12 V battery negative (-) lead → Terminal 2 (TEM+)


The steering column extends.


Text in Illustration
*a Component without harness connected
(Telescopic Motor)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
a.

Disconnect the E144 multiplex tilt and telescopic ECU connector.


b.

Disconnect the E142 telescopic motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E144-14 (VCE) - E142-5 (VCE) Always Below 1 Ω
E144-15 (TES) - E142-4 (TES)
E144-17 (E2) - E142-3 (E2)
E144-14 (VCE) - Body ground 10 kΩ or higher
E144-15 (TES) - Body ground
E144-17 (E2) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

OK

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)
a.
U165144E01
0.155,0.086 0.357,0.260 0.202,0.174 10 *a 1.544,0.354 1.945,0.545 0.401,0.191 10 E144 1.647,1.458 1.972,1.632 0.325,0.174 10 VCE 1.089,1.458 1.434,1.632 0.346,0.174 10 E2 1.815,1.426 1.738,1.15 false 1.231,1.426 1.308,1.15 false

Reconnect the multiplex tilt and telescopic ECU connector.


b.

Disconnect the E142 telescopic motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E144-14 (VCE) - E144-17 (E2) Engine switch on (IG) 8 to 14 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

9.CHECK TELESCOPIC POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

9.CHECK TELESCOPIC POSITION SENSOR
a.
U165145E02
1.688,1.458 1.594,1.177 false 1.188,1.448 1.302,1.167 false 0.167,0.115 0.365,0.292 0.198,0.177 10 false *a 1.563,0.385 1.948,0.563 0.385,0.177 10 false E144 1.604,1.5 1.948,1.677 0.344,0.177 10 false TES 1.073,1.49 1.417,1.667 0.344,0.177 10 false E2

Reconnect the multiplex tilt and telescopic ECU connector.


b.

Reconnect the E142 telescopic motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E144-15 (TES) - E144-17 (E2) Steering column contracting or extending Pulse generation
High: 8 to 14 V
Low: Below 1 V


Text in Illustration
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG