Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255455 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) G

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 2.REMOVE LOWER STEERING COLUMN COVER

a.
C172704

Remove the 3 screws.

HINT:

Turn the steering wheel to the right and left as necessary to remove the 2 screws.



b.
C172708

Detach the 2 claws to remove the lower steering column cover.


Hide 45286B 3.REMOVE UPPER STEERING COLUMN COVER

a.

Detach the 4 clips.


b.
C172706

Detach the claw to remove the upper steering column cover.


Hide 73900 4.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

Hide 5.INSPECT TILT MOTOR

a.

Inspect the tilt motor.

i.

Disconnect connector A from the multiplex tilt and telescopic ECU.


ii.
C172660E06
2.292,3.688 2.698,3.229 true 2.313,3.979 2.667,4.302 true 1.719,1.948 1.938,2.167 0.219,0.219 10 false *1 2.771,3.125 3.281,3.365 0.51,0.24 10 false TIM- (-) 2.76,4.25 3.333,4.49 0.573,0.24 10 false TIM+ (+) 0.49,2.677 0.708,2.896 0.219,0.219 10 false *a

Apply battery voltage to the tilt motor connector, and check the steering wheel tilt operation.

Text in Illustration
*1 Connector A
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (TIM+)
Battery negative (-) → Terminal 1(TIM-)
Steering wheel tilts up


iii.
C172660E06
2.292,3.688 2.698,3.229 true 2.313,3.979 2.667,4.302 true 1.719,1.948 1.938,2.167 0.219,0.219 10 false *1 2.771,3.125 3.281,3.365 0.51,0.24 10 false TIM- (-) 2.76,4.25 3.333,4.49 0.573,0.24 10 false TIM+ (+) 0.49,2.677 0.708,2.896 0.219,0.219 10 false *a

Apply battery voltage to the tilt motor connector, and check the steering wheel tilt operation.

Text in Illustration
*1 Connector A
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (TIM-)
Battery negative (-) → Terminal 10 (TIM+)
Steering wheel tilts down

If the steering wheel does not tilt down, replace the steering column assembly.



Hide 6.INSPECT TELESCOPIC MOTOR

a.

Inspect the telescopic motor.

i.

Disconnect connector B from the multiplex tilt and telescopic ECU.


ii.
C172661E05
1.24,3.51 0.823,3.313 true 1.24,4.073 0.833,4.198 true 0.823,0.719 1.052,0.969 0.229,0.25 10 true *1 0.354,3.188 0.833,3.375 0.479,0.188 10 false TEM+ 0.406,4.125 0.823,4.313 0.417,0.188 10 false TEM- 0.302,2.5 0.615,2.698 0.313,0.198 10 false *a

Apply battery voltage to the telescopic motor connector, and check the steering column operation.

Text in Illustration
*1 Connector B
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (TEM+)
Battery negative (-) → Terminal 6 (TEM-)
Steering column contracts


iii.
C172661E05
1.24,3.51 0.823,3.313 true 1.24,4.073 0.833,4.198 true 0.823,0.719 1.052,0.969 0.229,0.25 10 true *1 0.354,3.188 0.833,3.375 0.479,0.188 10 false TEM+ 0.406,4.125 0.823,4.313 0.417,0.188 10 false TEM- 0.302,2.5 0.615,2.698 0.313,0.198 10 false *a

Apply battery voltage to the telescopic motor connector, and check the steering column operation.

Text in Illustration
*1 Connector B
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (TEM-)
Battery negative (-) → Terminal 2 (TEM+)
Steering column extends

If the steering column operation does not match the specified condition, replace the steering column.



Hide 73900 7.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

Hide 8.INSTALL LOWER STEERING COLUMN COVER

a.
C172708

Attach the 2 claws to install the lower steering column cover.


Hide 45286B 9.INSTALL UPPER STEERING COLUMN COVER

a.
C172706

Attach the claw to install the upper steering column cover.


b.

Attach the 4 clips to install the upper steering cover onto the instrument panel cluster finish panel.


c.
C172704

Install the 3 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)

HINT:

Turn the steering wheel to the right and left as necessary to install the 2 screws.



Hide 10.INSPECT SRS WARNING LIGHT

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).