Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255476 REAR SEAT ENTERTAINMENT SYSTEM C

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  B15CE  Seatback Display Disconnected  


DESCRIPTION

The television display assembly and multi-display controller sub-assembly are connected by an AVC-LAN communication line.

The multi-media module receiver assembly is connected to the multi-display controller sub-assembly by a MOST communication line.

This DTC will be stored when an AVC-LAN communication error occurs between the multi-display controller sub-assembly and television display assembly.

DTC Code DTC Detection Condition Trouble Area
B15CE Either condition is met:
·

The television display assembly is not connected while the engine switch is on (IG) or (ACC).

·

Communication between the master unit and television display assembly is not possible when the engine is started.


·

Television display assembly power source circuit

·

AVC-LAN circuit between multi-display controller sub-assembly and television display assembly

·

Multi-display controller sub-assembly

·

Television display assembly LH

·

Television display assembly RH



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The multi-media module receiver assembly is the master unit.



WIRING DIAGRAM

U166098E02
3.354,0.26 3.823,0.49 0.469,0.229 10 false GND4 3.344,0.729 3.844,0.948 0.5,0.219 10 false PWR2 3.365,1.229 3.865,1.438 0.5,0.208 10 false GND2 3.406,1.708 3.813,1.885 0.406,0.177 10 false TX2+ 3.427,2.198 3.802,2.406 0.375,0.208 10 false TX2- 5.604,0.26 6.073,0.49 0.469,0.229 10 false GND2 5.604,0.729 6.104,0.948 0.5,0.219 10 false PWR2 5.604,1.219 6.104,1.427 0.5,0.208 10 false GND 5.604,1.688 6.01,1.865 0.406,0.177 10 false TX2+ 5.604,2.177 5.979,2.385 0.375,0.208 10 false TX2- 3.354,3.031 3.813,3.24 0.458,0.208 10 false GND3 3.344,3.5 3.792,3.719 0.448,0.219 10 false PWR1 3.354,4 3.802,4.24 0.448,0.24 10 false GND1 3.385,4.469 3.76,4.688 0.375,0.219 10 false TX1+ 3.406,4.948 3.76,5.135 0.354,0.188 10 false TX1- 5.604,3.031 6.063,3.24 0.458,0.208 10 false GND4 5.604,3.5 6.052,3.719 0.448,0.219 10 false PWR1 5.604,4 6.052,4.24 0.448,0.24 10 false GND6 5.604,4.469 5.979,4.688 0.375,0.219 10 false TX1+ 5.604,4.948 5.958,5.135 0.354,0.188 10 false TX1- 3.927,0.052 4.208,0.26 0.281,0.208 10 false 11 3.979,0.521 4.208,0.677 0.229,0.156 10 false 2 3.927,1.021 4.146,1.208 0.219,0.188 10 false 10 3.927,1.5 4.167,1.688 0.24,0.188 10 false 12 3.917,1.979 4.177,2.146 0.26,0.167 10 false 13 3.927,2.813 4.188,3.031 0.26,0.219 10 false 13 3.969,3.292 4.156,3.469 0.188,0.177 10 false 3 3.927,3.781 4.115,3.958 0.188,0.177 10 false 12 3.927,4.26 4.115,4.406 0.188,0.146 10 false 10 3.938,4.75 4.177,4.958 0.24,0.208 10 false 11 2.563,5.229 4.042,5.552 1.479,0.323 10 false Multi-display Controller Sub-assembly 5.063,2.615 7.104,2.792 2.042,0.177 10 false Television Display Assembly LH 5.052,5.375 7.094,5.552 2.042,0.177 10 false Television Display Assembly RH 3.885,0.26 4.198,0.469 0.313,0.208 10 false L67 3.885,0.729 4.198,0.938 0.313,0.208 10 false L67 3.885,1.219 4.198,1.427 0.313,0.208 10 false L67 3.885,3.042 4.188,3.26 0.302,0.219 10 false L67 3.885,3.5 4.198,3.719 0.313,0.219 10 false L67 3.885,3.99 4.198,4.208 0.313,0.219 10 false L67 3.896,4.479 4.198,4.646 0.302,0.167 10 false L66 3.896,2.198 4.198,2.365 0.302,0.167 10 false L66 3.896,1.698 4.198,1.865 0.302,0.167 10 false L66 3.896,4.979 4.198,5.146 0.302,0.167 10 false L66 5.313,0.146 5.521,0.323 0.208,0.177 10 false 10 5.375,0.635 5.583,0.802 0.208,0.167 10 false 6 5.063,2.448 5.375,2.615 0.313,0.167 10 false c43 5.052,5.219 5.323,5.375 0.271,0.156 10 false c38 5.375,1.115 5.563,1.302 0.188,0.188 10 false 9 5.375,1.594 5.531,1.781 0.156,0.188 10 false 3 5.375,2.094 5.573,2.292 0.198,0.198 10 false 4 5.313,2.917 5.521,3.094 0.208,0.177 10 false 10 5.313,3.396 5.521,3.563 0.208,0.167 10 false 6 5.323,3.885 5.51,4.073 0.188,0.188 10 false 9 5.365,4.344 5.521,4.531 0.156,0.188 10 false 3 5.365,4.875 5.563,5.073 0.198,0.198 10 false 4 0.333,1.708 1.781,2.052 1.448,0.344 10 false Multi-media Module Receiver Assembly 0.344,1.531 0.875,1.729 0.531,0.198 10 false F102 1.229,0.49 1.563,0.677 0.333,0.188 10 false MI+ 1.24,1.01 1.51,1.208 0.271,0.198 10 false MI- 1.615,0.375 1.854,0.583 0.24,0.208 10 false 2 1.615,0.896 1.844,1.104 0.229,0.208 10 false 3 2.406,0.49 2.729,0.698 0.323,0.208 10 false L77 2.406,1.021 2.74,1.229 0.333,0.208 10 false L77 2.49,0.813 2.667,1.031 0.177,0.219 10 false 6 2.479,0.292 2.667,0.479 0.188,0.188 10 false 5 2.792,0.5 3.177,0.708 0.385,0.208 10 false MO+ 2.802,1.01 3.167,1.208 0.365,0.198 10 false MO-

PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs and check if the same trouble occurs again (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

3.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

NG

3.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result
Result Proceed to
Optional components (including associated wiring) are installed A
Optional components (including associated wiring) are not installed B



A

4.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

5.CLEAR DTC
4.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

5.CLEAR DTC
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs and check if the same trouble occurs again (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END

NG

7.CHECK OPERATION
7.CHECK OPERATION
a.

Check which television display assembly does not operate.

Result
Result Proceed to
Television display assembly LH does not operate A
Television display assembly RH does not operate B



A

8.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH POWER SOURCE)

B

12.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH POWER SOURCE)
8.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH POWER SOURCE)
a.
U155737E01
0.08,0.025 0.249,0.191 0.170,0.166 10 *a 2.489,0.999 2.969,1.165 0.480,0.166 10 PWR2 0.748,1.836 1.186,2.002 0.438,0.166 10 GND 2.162,1.836 2.638,2.002 0.475,0.166 10 GND2 1.611,0.437 1.873,0.604 0.262,0.166 10 c43 2.148,1.287 2.453,1.111 false 1.605,1.546 1.166,1.904 false 1.837,1.553 2.129,1.904 false

Disconnect the television display assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
c43-6 (PWR2) - c43-9 (GND) Engine switch on (IG) 11 to 14 V
c43-6 (PWR2) - c43-10 (GND2) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly LH)



OK

9.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY LH)

NG

11.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY LH)
9.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY LH)
a.

Disconnect the L66 multi-display controller sub-assembly connector.


b.

Disconnect the c43 television display assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L66-12 (TX2+) - c43-3 (TX2+) Always Below 1 Ω
L66-13 (TX2-) - c43-4 (TX2-) Always Below 1 Ω
L66-12 (TX2+) - Body ground Always 10 kΩ or higher
L66-13 (TX2-) - Body ground Always 10 kΩ or higher




OK

10.CHECK TELEVISION DISPLAY ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TELEVISION DISPLAY ASSEMBLY LH
a.

Replace the television display assembly LH (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).



c.

Check for DTCs and check if the same trouble occurs again.

OK:

No DTCs are output.




OK

END (TELEVISION DISPLAY ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY LH)
a.

Disconnect the L67 multi-display controller sub-assembly connector.


b.

Disconnect the c43 television display assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L67-2 (PWR2) - c43-6 (PWR2) Always Below 1 Ω
L67-10 (GND2) - c43-9 (GND) Always Below 1 Ω
L67-11 (GND4) - c43-10 (GND2) Always Below 1 Ω
L67-2 (PWR2) - Body ground Always 10 kΩ or higher
L67-10 (GND2) - Body ground Always 10 kΩ or higher
L67-11 (GND4) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH POWER SOURCE)
a.
U163863E01
0.08,0.025 0.249,0.191 0.170,0.166 10 *a 2.489,0.999 2.969,1.165 0.480,0.166 10 PWR1 0.624,1.836 1.062,2.002 0.438,0.166 10 GND6 2.162,1.836 2.638,2.002 0.475,0.166 10 GND4 1.611,0.437 1.873,0.604 0.262,0.166 10 c38 2.148,1.287 2.453,1.111 false 1.605,1.546 1.166,1.904 false 1.837,1.553 2.129,1.904 false

Disconnect the television display assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
c38-6 (PWR1) - c38-9 (GND6) Engine switch on (IG) 11 to 14 V
c38-6 (PWR1) - c38-10 (GND4) Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Television Display Assembly RH)


OK

13.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY RH)

NG

15.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY RH)
13.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY RH)
a.

Disconnect the L66 multi-display controller sub-assembly connector.


b.

Disconnect the c38 television display assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L66-10 (TX1+) - c38-3 (TX1+) Always Below 1 Ω
L66-11 (TX1-) - c38-4 (TX1-) Always Below 1 Ω
L66-10 (TX1+) - Body ground Always 10 kΩ or higher
L66-11 (TX1-) - Body ground Always 10 kΩ or higher




OK

14.CHECK TELEVISION DISPLAY ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK TELEVISION DISPLAY ASSEMBLY RH
a.

Replace the television display assembly RH (See page Audio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL).



c.

Check for DTCs and check if the same trouble occurs again.

OK:

No DTCs are output.




OK

END (TELEVISION DISPLAY ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - TELEVISION DISPLAY ASSEMBLY RH)
a.

Disconnect the L67 multi-display controller sub-assembly connector.


b.

Disconnect the c38 television display assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L67-3 (PWR1) - c38-6 (PWR1) Always Below 1 Ω
L67-12 (GND1) - c38-9 (GND6) Always Below 1 Ω
L67-13 (GND3) - c38-10 (GND4) Always Below 1 Ω
L67-3 (PWR1) - Body ground Always 10 kΩ or higher
L67-12 (GND1) - Body ground Always 10 kΩ or higher
L67-13 (GND3) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR