Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Stereo Component Amplifier) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255477 AUDIO AND VISUAL SYSTEM(w/o Stereo Component Amplifier) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Stereo Component Amplifier)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E159230E02
2.129,0.75 3.179,0.933 1.049,0.184 10 from TAIL Relay 3.896,3.411 4.189,3.595 0.293,0.184 10 z36 5.236,3.195 5.385,3.378 0.149,0.184 10 4 6.245,2.091 6.602,2.274 0.357,0.184 10 GND 6.245,0.772 6.602,0.955 0.357,0.184 10 ILL+ 6.238,3.414 6.595,3.598 0.357,0.184 10 SWG 5.939,1.846 6.119,2.029 0.180,0.184 10 7 5.904,0.533 6.109,0.717 0.205,0.184 10 10 5.923,3.183 6.072,3.367 0.149,0.184 10 6 6.111,4.087 7.087,4.271 0.975,0.184 10 Radio Receiver 4.441,3.531 4.778,3.715 0.337,0.184 10 EAU 3.964,3.187 4.104,3.370 0.140,0.184 10 8 3.91,5.758 4.189,5.941 0.279,0.184 10 z36 5.138,5.755 5.426,5.938 0.288,0.184 10 E12 5.138,3.422 5.426,3.606 0.288,0.184 10 E12 5.854,3.416 6.142,3.600 0.288,0.184 10 F19 5.847,2.085 6.133,2.269 0.286,0.184 10 F35 5.861,0.773 6.159,0.957 0.298,0.184 10 F35 4.441,5.892 4.764,6.075 0.323,0.184 10 IL+2 4.259,6.319 5.082,6.503 0.823,0.184 10 Spiral Cable 0.32,7.069 1.617,7.252 1.297,0.184 10 Steering Pad Switch 1.585,6.375 2.170,6.559 0.584,0.184 10 RH Side 1.585,4.075 2.170,4.259 0.584,0.184 10 LH Side 3.964,5.541 4.138,5.724 0.175,0.184 10 5 5.183,5.541 5.357,5.724 0.175,0.184 10 12 3.789,0.922 4.264,1.078 0.475,0.156 10 PANEL

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch. A
Illumination comes on for all components except radio receiver. B
No illumination comes on for radio receiver, glove box light, front seat memory switch, cigarette lighter, etc. C



A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - TAIL RELAY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - TAIL RELAY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - TAIL RELAY)
U166087E01
0.156,0.11 0.353,0.285 0.198,0.174 10 *1 2.341,1.743 2.659,1.917 0.318,0.174 10 IL+2 2.161,1.371 2.492,1.701 false 0.471,0.882 0.735,1.064 0.264,0.181 10 E12

a.

Disconnect the E12 cable connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E12-12 (IL+2) - Body ground Light control switch tail or head 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Spiral Cable)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
E155691E01
4.524,1.457 4.875,1.641 0.350,0.184 10 EAU 4.524,1.085 4.833,1.255 0.309,0.170 10 IL+2 4.503,1.16 4.315,1.16 4.315,1.16 4.109,1.488 false 3.871,1.634 4.334,1.522 4.334,1.522 4.488,1.522 false 5.363,1.008 5.580,1.174 0.218,0.166 10 (+) 5.381,1.425 5.575,1.591 0.194,0.166 10 (-)

a.

Disconnect the z36 switch connector.


b.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (IL+2)
Battery negative (-) → Terminal 8 (EAU)
Light illuminates




OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
U166068E02
1.969,2.094 1.74,1.917 false 1.406,1.625 1.75,1.146 false 5.458,1.49 4.99,1.719 false 5.938,0.938 5.76,1.25 false 0.99,1.094 1.24,1.25 0.25,0.156 10 false z36 4.792,0.854 5.073,1.01 0.281,0.156 10 false E12 2.01,2.052 2.323,2.229 0.313,0.177 10 false EAU 4.708,1.74 5.021,1.917 0.313,0.177 10 false EAU 0.844,2.292 2.5,2.458 1.656,0.167 10 false *a 4.708,2.021 5.563,2.208 0.854,0.188 10 false *b 1.802,1.052 2.146,1.198 0.344,0.146 10 false IL+2 5.958,0.802 6.281,0.979 0.323,0.177 10 false IL+2

Text in Illustration
*a Steering Pad Switch Side *b Vehicle Side

a.

Disconnect the E12 and z36 cable connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-12 (IL+2) - z36-5 (IL+2) Spiral cable is turned 2.5 rotations counterclockwise Below 3 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
E12-4 (EAU) - z36-8 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 3 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise


CAUTION:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).




OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
a.

Disconnect the F19 receiver connector.


b.

Disconnect the E12 cable connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-6 (SWG) - E12-4 (EAU) Always Below 1 Ω
F19-6 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - TAIL RELAY AND BODY GROUND)
a.
U165770E02
1.594,1.521 1.74,1.896 false 2.354,1.531 2.5,1.906 false 0.146,0.094 0.375,0.292 0.229,0.198 10 false *1 1.76,1.927 2.104,2.094 0.344,0.167 10 false GND 2.542,1.958 2.865,2.115 0.323,0.156 10 false ILL+ 0.333,1.156 0.594,1.333 0.26,0.177 10 false F35

Disconnect the F35 receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F35-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F35-10 (ILL+) - Body ground Light control switch
tail or head
11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Radio Receiver)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR