Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result
Result Proceed to
Automatic station search function stops on a station. A
Automatic station search function does not stop. B




A

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

B

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check optional components (sunshade film, telephone antenna, etc.).

i.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result
Result Proceed to
Optional components are installed. A
Optional components are not installed. B

NOTICE:

Do not remove any optional components installed by the customer without his or her consent.





A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

B

3.CHECK RADIO ANTENNA
3.CHECK RADIO ANTENNA
a.

Check for noise

i.

Turn the engine switch on (ACC) with the multi-media module receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the antenna and check that noise can be heard from the speakers.

Result
Result Proceed to
Noise does not occur. A
Noise occurs. B




A

4.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

B

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

4.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the multi-media module receiver assembly.



b.

Check for noise

i.

Turn the engine switch on (ACC) with the multi-media module receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the multi-media module receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speaker.





OK

5.CHECK WINDOW GLASS ANTENNA WIRE

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994E23
0.177,0.604 0.427,0.802 0.25,0.198 10 false *1 0.594,1.885 0.844,2.083 0.25,0.198 10 false *2 1.896,1.521 2.146,1.719 0.25,0.198 10 false *3

Check for continuity of the antenna.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.


OK:

There is continuity in the antenna.


Text in Illustration
*1 Tester Probe
*2 Antenna Wire
*3 Tin Foil



OK

6.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

6.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.

Disconnect the multi-media module receiver assembly connector.


b.
U118209E01
0.095,0.051 0.271,0.228 0.177,0.177 10 *a 0.772,0.971 1.066,1.121 0.295,0.150 10 RA 0.705,1.404 1.108,1.575 0.402,0.171 10 ANT+ 1.552,1.083 1.136,1.404 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
RA-5 (ANT+) - Body ground Engine switch on (ACC)
Radio switch on
11 to 14 V


Text in Illustration
*a Component without harness connected
(Multi-media Module Receiver Assembly)



OK

7.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

7.CHECK ANTENNA CORD SUB-ASSEMBLY
a.

Remove the antenna connector of the multi-media module receiver assembly and antenna.


b.

Measure the resistance between the antenna and multi-media module receiver assembly to check for an open circuit in the antenna cord.

Standard resistance:

Below 1 Ω



c.

Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

Standard resistance:

10 kΩ or higher




OK

8.CHECK AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

8.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received.




OK

END

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY