Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  B15D6  Display Disconnected  


DESCRIPTION

The multi-display assembly and multi-media module receiver assembly are connected by an AVC-LAN communication line.

When an AVC-LAN communication error occurs between the display module board and multi-display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D6* A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Multi-display assembly

·

Multi-media module receiver assembly

·

Harness or connector



HINT:
·

*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The multi-media module receiver assembly is the master unit.



WIRING DIAGRAM

C260261E01
2.829,2.017 4.403,2.203 1.574,0.186 10 Multi-display Assembly 2.82,1.877 3.176,2.034 0.356,0.157 10 F79 5.384,2.033 6.664,2.413 1.280,0.379 10 Multi-media Module Receiver Assembly 5.384,1.863 5.740,2.020 0.356,0.157 10 F77 2.733,1.313 2.942,1.486 0.208,0.173 10 13 2.733,0.935 2.942,1.107 0.208,0.173 10 24 2.733,0.514 2.942,0.687 0.208,0.173 10 23 3.936,0.893 4.142,1.065 0.206,0.173 10 19 3.936,0.472 4.142,0.645 0.206,0.173 10 7 5.295,0.907 5.501,1.079 0.206,0.173 10 46 5.295,0.486 5.501,0.659 0.206,0.173 10 45 3.015,1.419 3.473,1.576 0.458,0.157 10 GND1 3.015,1.04 3.395,1.198 0.379,0.157 10 ACC 3.015,0.62 3.436,0.777 0.421,0.157 10 IG 2.729,0.136 2.937,0.309 0.208,0.173 10 12 3.011,0.242 3.432,0.399 0.421,0.157 10 +B2 3.615,1.012 4.034,1.169 0.419,0.157 10 TX- 3.585,0.592 4.006,0.749 0.421,0.157 10 TX+ 5.546,1.026 5.926,1.184 0.379,0.157 10 TX3- 5.546,0.606 5.926,0.763 0.379,0.157 10 TX3+ 0.274,1.01 1.414,1.179 1.140,0.170 10 from ACC Relay 0.433,0.234 1.221,0.404 0.788,0.170 10 from Battery 0.024,0.608 1.377,0.778 1.353,0.170 10 from IG1 No. 1 Relay 1.449,0.753 2.456,0.908 1.008,0.155 10 ECU-IG1 No. 1 1.776,0.386 2.202,0.556 0.426,0.170 10 TV 1.711,1.152 2.137,1.322 0.426,0.170 10 ACC 0.655,2.317 2.703,2.526 2.048,0.209 10 : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

DTC B15D6 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166140E01
1.551,0.401 1.835,0.567 0.284,0.166 10 F79 2.604,0.507 2.876,0.677 0.272,0.170 10 +B2 0.125,0.056 0.396,0.226 0.272,0.170 10 *a 2.604,1.785 2.940,1.982 0.336,0.198 10 ACC 0.289,1.733 0.732,1.908 0.443,0.174 10 GND1 2.501,1.504 2.684,1.779 false 0.905,1.48 0.57,1.699 false 1.793,1.841 2.000,2.015 0.207,0.174 10 IG 2.314,1.519 1.949,1.823 false 2.49,1.219 2.673,0.696 false

Disconnect the multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-12 (+B2) - F79-13 (GND1) Always 11 to 14 V
F79-23 (IG) - F79-13 (GND1) Engine switch on (IG) 11 to 14 V
F79-24 (ACC) - F79-13 (GND1) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display assembly)


OK

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E57
2.698,1.781 2.521,1.781 2.521,1.781 2.385,1.344 true 1.958,1.771 2.115,1.771 2.115,1.771 2.26,1.333 true 1.656,1.698 1.99,1.917 0.333,0.219 10 false TX3- 2.781,1.708 3.198,1.906 0.417,0.198 10 false TX3+

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F79 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-45 (TX3+) - F79-7 (TX+) Always Below 1 Ω
F77-46 (TX3-) - F79-19 (TX-) Always Below 1 Ω
F77-45 (TX3+) - Body ground Always 10 kΩ or higher
F77-46 (TX3-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).



NEXT

7.CLEAR DTC
8.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

DTC B15D6 is not output.




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY