Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/ Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255478 AUDIO AND VISUAL SYSTEM(w/ Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Navigation System)  B15F9  UART Communication Malfunction(for A/C)  


DESCRIPTION

The multi-media module receiver assembly and multi-display assembly are connected by the UART communication line.

When a UART communication error occurs between the multi-media module receiver assembly and multi-display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15F9 Multi-display for air conditioning switch operation signal input malfunction.
·

Multi-display assembly

·

Multi-media module receiver assembly

·

Harness or connector



WIRING DIAGRAM

E235206E31
1.042,1.792 1.479,1.958 0.438,0.167 10 false F79 1.042,1.969 2.885,2.302 1.844,0.333 10 false Multi-display Assembly 5.156,1.792 5.656,1.958 0.5,0.167 10 false F77 5.198,1.344 5.896,1.51 0.698,0.167 10 false UIND 4.958,1.25 5.167,1.417 0.208,0.167 10 false 35 5.198,0.781 5.781,0.979 0.583,0.198 10 false UPSW 4.948,0.698 5.125,0.865 0.177,0.167 10 false 36 1.604,1.313 2.021,1.479 0.417,0.167 10 false UIND 2.063,1.229 2.271,1.396 0.208,0.167 10 false 4 1.604,0.76 2.021,0.927 0.417,0.167 10 false UPSW 2.063,0.677 2.271,0.844 0.208,0.167 10 false 3 5.156,1.969 6.458,2.427 1.302,0.458 10 false Multi-media Module Receiver Assembly

PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F79 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-36 (UPSW) - F79-3 (UPSW) Always Below 1 Ω
F77-35 (UIND) - F79-4 (UIND) Always Below 1 Ω
F77-36 (UPSW) - Body ground Always 10 kΩ or higher
F77-35 (UIND) - Body ground Always 10 kΩ or higher




OK

4.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/ Navigation System)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY