Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Illumination Circuit  


CAUTION / NOTICE / HINT

DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E194893E02
2.265,0.423 3.388,0.667 1.123,0.244 10 from TAIL Relay 3.911,0.582 4.424,0.826 0.512,0.244 10 PANEL 6.242,3.409 6.779,3.574 0.538,0.165 10 SWG 6.134,3.782 7.130,3.960 0.996,0.178 10 Radio Receiver 5.93,3.22 6.082,3.386 0.151,0.165 10 6 5.216,3.22 5.367,3.386 0.151,0.165 10 4 3.962,3.22 4.113,3.386 0.151,0.165 10 8 5.176,5.58 5.369,5.745 0.193,0.165 10 12 3.958,5.576 4.109,5.741 0.151,0.165 10 5 5.84,3.428 6.188,3.593 0.348,0.165 10 F19 5.132,3.428 5.480,3.593 0.348,0.165 10 E12 3.892,3.428 4.240,3.593 0.348,0.165 10 z36 5.132,5.772 5.480,5.938 0.348,0.165 10 E12 3.892,5.772 4.240,5.938 0.348,0.165 10 z36 4.46,3.546 4.822,3.711 0.362,0.165 10 EAU 4.474,5.875 4.801,6.040 0.327,0.165 10 IL+2 4.215,6.295 5.073,6.461 0.858,0.165 10 Spiral Cable 1.595,6.782 2.203,6.947 0.608,0.165 10 RH Side 1.595,4.106 2.203,4.271 0.608,0.165 10 LH Side 0.369,7.335 1.977,7.500 1.608,0.165 10 Steering Pad Switch 1.21,1.049 1.625,1.251 0.415,0.202 10 ACAN 1.702,0.965 1.978,1.167 0.276,0.202 10 16 0.855,1.504 1.131,1.707 0.276,0.202 10 E2 0.855,1.665 2.131,1.868 1.276,0.202 10 Main Body ECU 5.864,1.072 6.212,1.237 0.348,0.165 10 F19 6.233,1.074 6.771,1.239 0.538,0.165 10 ADIM 5.892,0.855 6.070,1.020 0.178,0.165 10 20

CAUTION / NOTICE / HINT

CAUTION:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the multi-display, steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch. A
Illumination comes on for all components except radio receiver. B
No illumination comes on for radio receiver, multi-display, glove box light, front seat memory switch, cigarette lighter, etc. C



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MAIN BODY ECU)

C

2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)
U166087E01
0.156,0.11 0.353,0.285 0.198,0.174 10 *1 2.341,1.743 2.659,1.917 0.318,0.174 10 IL+2 2.161,1.371 2.492,1.701 false 0.471,0.882 0.735,1.064 0.264,0.181 10 E12

a.

Disconnect the E12 cable connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E12-12 (IL+2) - Body ground Always 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Spiral Cable)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY (STEERING PAD SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY (STEERING PAD SIDE)
E154802E04
4.01,1.5 4.26,1.167 4.26,1.167 4.417,1.167 false 3.729,1.656 4.177,1.552 4.177,1.552 4.365,1.552 false 4.469,1.479 4.792,1.677 0.323,0.198 10 false EAU 4.448,1.083 4.823,1.271 0.375,0.188 10 false IL+2 5.26,0.99 5.5,1.177 0.24,0.188 10 false (+) 5.281,1.417 5.448,1.604 0.167,0.188 10 false (-)

a.

Disconnect the z36 switch connector.


b.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (IL+2)
Battery negative (-) → Terminal 8 (EAU)
Light illuminates



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLE

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLE
U166070E02
1.979,2.094 1.75,1.917 false 1.438,1.635 1.781,1.156 false 5.469,1.479 4.99,1.708 false 5.927,0.927 5.76,1.24 false 0.99,1.104 1.24,1.26 0.25,0.156 10 false z36 4.792,0.854 5.073,1.01 0.281,0.156 10 false E12 2.063,2.042 2.375,2.219 0.313,0.177 10 false EAU 4.75,1.74 5.063,1.917 0.313,0.177 10 false EAU 1.688,2.302 1.865,2.469 0.177,0.167 10 false *2 5.448,2 5.635,2.188 0.188,0.188 10 false *1 1.854,1.052 2.198,1.198 0.344,0.146 10 false IL+2 5.979,0.781 6.302,0.958 0.323,0.177 10 false IL+2

Text in Illustration
*1 Vehicle Side *2 Steering Pad Switch Side


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-12 (IL+2) - z36-5 (IL+2) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
E12-4 (EAU) - z36-8 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise


CAUTION:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).




OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
a.

Disconnect the F19 radio receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-6 (SWG) - E12-4 (EAU) Always Below 1 Ω
F19-6 (SWG) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MAIN BODY ECU)
a.

Disconnect the F19 receiver connector.


b.

Disconnect the E2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-20 (ADIM) - E2-16 (ACAN) Always Below 1 Ω
F19-20 (ADIM) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR