Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The circuit is necessary for the Automatic Sound Levelizer (ASL) built into the stereo component amplifier assembly.

Speed signals are received from the combination meter assembly and used for the ASL.

The ASL function automatically adjusts the sound volume in order to clear audio quality even when vehicle noise increases (as vehicle noise increases, the volume is turned up etc.).

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E194845E12
5.125,1.813 5.448,2.031 0.323,0.219 10 false +S 4.917,1.688 5.146,1.906 0.229,0.219 10 false 4 4.885,3.167 5.115,3.385 0.229,0.219 10 false 11 2.865,1.688 3.094,1.906 0.229,0.219 10 false 11 3.823,1.688 4.052,1.906 0.229,0.219 10 false 61 5.146,0.698 5.469,0.917 0.323,0.219 10 false SI 4.917,0.625 5.146,0.844 0.229,0.219 10 false 3 1.479,0.813 1.802,1.031 0.323,0.219 10 false SP1 5.146,3.323 5.469,3.542 0.323,0.219 10 false SPD 1.875,0.615 2.104,0.833 0.229,0.219 10 false 12 0.531,1.427 1.885,1.708 1.354,0.281 10 false Skid Control ECU 4.729,2.448 6.688,2.74 1.958,0.292 10 false Combination Meter Assembly 4.948,3.969 6.177,4.49 1.229,0.521 10 false Stereo Component Amplifier Assembly 2.823,3.875 4.219,4.167 1.396,0.292 10 false Junction Connector 2.823,2.427 4.24,2.74 1.417,0.313 10 false Junction Connector 3.802,3.167 4.031,3.385 0.229,0.219 10 false 6 2.938,3.167 3.167,3.385 0.229,0.219 10 false 1 2.823,3.688 3.167,3.948 0.344,0.26 10 false F22 4.958,3.823 5.354,4.01 0.396,0.188 10 false F18 2.833,2.271 3.26,2.5 0.427,0.229 10 false E58 4.729,2.271 5.104,2.51 0.375,0.24 10 false E7 0.542,1.229 0.958,1.5 0.417,0.271 10 false A24

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U166128E01
0.276,1.135 0.615,1.310 0.339,0.174 10 E7 2.674,0.59 2.106,1.247 false 2.705,0.499 2.945,0.672 0.240,0.173 10 +S 0.78,3.803 0.78,4.176 false 1.467,3.807 1.467,4.176 false 0.866,4.086 1.39,4.086 false 1.003,4.133 1.298,4.296 0.295,0.163 10 (A) 2.86,3.717 3.234,3.880 0.375,0.163 10 GND 0.154,0.092 0.397,0.283 0.243,0.191 10 *1

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal E7-4 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal E7-4 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform is displayed as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*1 Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER)

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER)
a.

Disconnect the F18 stereo component amplifier assembly and E7 combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-11 (SPD) - E7-4 (+S) Always Below 1 Ω




OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR