Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning, no sound, or only an extremely faint sound, can be heard.

WIRING DIAGRAM

E153585E20
1.013,0.996 1.437,1.217 0.424,0.221 10 MUTE 5.781,0.992 6.205,1.218 0.424,0.227 10 MUTE 1.582,0.866 1.720,1.003 0.137,0.137 10 1 5.463,0.866 5.684,1.040 0.221,0.174 10 7 0.205,2.08 0.736,2.236 0.531,0.156 10 F18 0.209,2.253 2.666,2.473 2.457,0.221 10 Stereo Component Amplifier Assembly 5.445,2.08 5.716,2.231 0.272,0.151 10 F1 5.449,2.253 7.114,2.404 1.665,0.151 10 Radio Receiver Assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U165826E01
2.862,2.204 3.313,2.371 0.451,0.167 10 MUTE 2.502,2.282 2.847,2.282 false 1.571,1.427 1.860,1.590 0.288,0.163 10 F18 0.266,0.229 1.352,0.787 1.086,0.559 10 *1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F18-1 (MUTE) - Body ground Engine switch on (ACC), audio system is playing → Changing sources Above 2.5 V → Below 0.5 V


Text in Illustration
*1 Component with harness connected
(Stereo Component Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER)
a.

Disconnect the F1 radio receiver assembly and F18 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-7 (MUTE) - F18-1 (MUTE) Always Below 1 Ω
F1-7 (MUTE) - Body ground Always 10 kΩ or higher




OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
U165827E01
1.729,1.956 2.193,2.123 0.464,0.167 10 MUTE 0.225,0.19 0.479,0.362 0.254,0.172 10 *1 1.921,1.544 2.005,1.946 false 0.406,1.338 0.707,1.501 0.300,0.163 10 F1

Reconnect the F18 stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-7 (MUTE) - Body ground Engine switch on (ACC), audio system is playing Above 2.5 V


Text in Illustration
*1 Front view of wire harness connector
(to Radio Receiver Assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY