Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  01-DC  Transmission Error  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
01-DC
*1
Transmission to component shown by sub-code failed (Detecting this DTC does not always mean actual failure). If the same sub-code is stored in other components, check power source circuit and communication system of all components shown by sub-code

HINT:

*1: If the engine switch is turned off after idling for 60 seconds, this DTC may be stored when the engine is started again.


NOTICE:
·

Before starting troubleshooting, be sure to clear the DTCs stored due to the reason described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.

·

The radio receiver assembly is the master unit.

·

Be sure to clear and recheck for the DTCs after the inspection is completed to confirm that no DTCs are output.



CAUTION / NOTICE / HINT

NOTICE:

Be sure to read Description before performing the following procedure.


PROCEDURE

1.CHECK FOR DTC OF OTHER COMPONENTS
a.

Check if the component shown by the sub-code is displayed in the check result of the other components.

i.

Check if "01-DC" is output for the other components.


ii.

If "01-DC" is output for any other components, check if the same physical address is displayed.

Result
Result Proceed to
"01-DC" is output and the same physical address is displayed A
"01-DC" is not output or the same physical address is not displayed B

HINT:

For the list of the components shown by sub-codes, refer to the table in step 2.





A

2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE

B

4.CLEAR DTC
2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
a.

Enter diagnostic mode.

E110915E17
1.135,0.792 1.344,0.979 0.208,0.188 10 false *1 1.135,1.333 1.354,1.521 0.219,0.188 10 false *1 1.125,1.854 1.333,2.042 0.208,0.188 10 false *1 1.125,2.323 1.333,2.51 0.208,0.188 10 false *1 1.125,3.24 1.323,3.427 0.198,0.188 10 false *1 0.448,0.667 0.802,0.854 0.354,0.188 10 false *1 4.177,2.573 4.396,2.76 0.219,0.188 10 false *1 4.177,3.063 4.396,3.25 0.219,0.188 10 false *1 4.177,3.615 4.396,3.802 0.219,0.188 10 false *1 4.167,4.135 4.385,4.323 0.219,0.188 10 false *1 4.167,5 4.385,5.188 0.219,0.188 10 false *1 4.146,5.896 4.385,6.083 0.24,0.188 10 false *1 3.177,4.031 3.396,4.219 0.219,0.188 10 false *1 4.823,5.896 5.031,6.083 0.208,0.188 10 false *2 4.823,4.99 5.177,5.177 0.354,0.188 10 false *2 4.802,4.125 5.135,4.313 0.333,0.188 10 false *2 4.792,3.604 5.146,3.792 0.354,0.188 10 false *2 4.802,3.052 5.135,3.24 0.333,0.188 10 false *2 4.802,2.563 5.135,2.75 0.333,0.188 10 false *2 6.26,2.448 6.594,2.635 0.333,0.188 10 false *2 1.771,3.24 2.146,3.427 0.375,0.188 10 false *2 1.771,2.302 2.073,2.49 0.302,0.188 10 false *2 1.76,1.854 2.104,2.042 0.344,0.188 10 false *2 1.771,1.323 2.104,1.51 0.333,0.188 10 false *2 1.771,0.781 2.073,0.969 0.302,0.188 10 false *2 2.427,0.646 2.646,0.833 0.219,0.188 10 false *2 3.302,1.896 3.646,2.083 0.344,0.188 10 false *3 2.865,2.292 3.208,2.479 0.344,0.188 10 false *4 0.417,4.979 2.104,5.156 1.688,0.177 10 false *1: SEEK TRACK DOWN 0.427,5.26 1.948,5.438 1.521,0.177 10 false *2: SEEK TRACK UP 0.417,5.531 2.052,5.698 1.635,0.167 10 false *3: PRESET SWITCH "2" 0.427,5.792 2.063,5.958 1.635,0.167 10 false *4: PRESET SWITCH "3" 5.74,3.615 6.063,3.781 0.323,0.167 10 false DTC 3.406,1.26 5.854,1.469 2.448,0.208 10 false Component which has stored this code 2.021,0.198 3.5,0.375 1.479,0.177 10 false Service Check Mode 4.938,0.792 6.729,0.969 1.792,0.177 10 false Detailed Information Mode 3.677,4.469 6.385,4.802 2.708,0.333 10 false Continues to display detailed information of the first code. 3.594,5.302 6.594,5.656 3,0.354 10 false Continues to display detailed information when more DTCs are stored. 0.406,2.688 2.708,3.01 2.302,0.323 10 false Continues to display check result when more components are installed. 0.063,0.021 0.771,0.198 0.708,0.177 10 false Example


b.

Press preset switch "2" to change the mode to "Detailed Information Mode".


c.

Identify the component which has stored this code.

Component Table
Component Physical Address
Stereo component amplifier assembly 440
Radio receiver assembly 190
Multi-media interface ECU 388

HINT:
·

"P440" set by the stereo component amplifier assembly is shown in the preceding illustration as an example.

·




NEXT

3.CHECK COMPONENT WHICH HAS STORED THIS CODE
3.CHECK COMPONENT WHICH HAS STORED THIS CODE
a.

Select the component which has stored this code.

Component Table
Component Proceed to
Stereo component amplifier assembly Stereo component amplifier communication error (See page (Click here))
Radio receiver assembly Radio receiver communication error (See page (Click here))
Multi-media interface ECU Multi-media interface ECU communication error (See page (Click here))



NEXT

END

4.CLEAR DTC
a.

Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/o Navigation System)>DTC CHECK / CLEAR).

HINT:

If "01-DC" is output for only one component, this may not indicate a malfunction.




NEXT

5.RECHECK FOR DTC
5.RECHECK FOR DTC
a.

Recheck for DTCs and check if the same trouble occurs again.

OK:

Malfunction disappears.




OK

END

NG

6.CHECK COMPONENT WHICH HAS STORED THIS CODE
6.CHECK COMPONENT WHICH HAS STORED THIS CODE
a.

Select the component which has stored this code.

Component Table
Component Proceed to
Stereo component amplifier assembly Stereo component amplifier communication error (See page (Click here))
Radio receiver assembly Radio receiver communication error (See page (Click here))
Multi-media interface ECU Multi-media interface ECU communication error (See page (Click here))



NEXT

END