Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  01-DF  Master Error  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
01-DF
*1
The device with a display fails and the master unit is switched to the audio device.
Also when a communication error between the sub-master unit (audio) and master unit occurs, this DTC is stored.
·

Radio receiver assembly power source circuit

·

AVC-LAN circuit between the radio receiver assembly and component which has stored this code

·

Radio receiver assembly

·

Component which has stored this code



HINT:

*1: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the engine switch on (IG) or (ACC), this DTC is stored.


NOTICE:
·

Before starting troubleshooting, be sure to clear the DTCs stored due to the reason described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.

·

The radio receiver assembly is the master unit.

·

Be sure to clear and recheck for the DTCs after the inspection is completed to confirm that no DTCs are output.



CAUTION / NOTICE / HINT

NOTICE:

Be sure to read Description before performing the following procedure.


PROCEDURE

1.CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
HINT:

Refer to Radio Receiver Power Source Circuit (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/o Navigation System)>Radio Receiver Power Source Circuit).


If the power source circuit is operating normally, proceed to the next step.


NEXT

2.INSPECT RADIO RECEIVER ASSEMBLY
2.INSPECT RADIO RECEIVER ASSEMBLY
a.
U166127E01
0.12,0.1 0.276,0.287 0.156,0.186 10 *1 0.12,2.655 0.297,2.811 0.178,0.156 10 *2 1.56,0.497 1.790,0.671 0.230,0.174 10 F1 0.338,3.789 0.604,3.941 0.266,0.152 10 F55 0.51,0.613 0.902,0.752 0.392,0.139 10 ATX+ 2.263,2.391 2.663,2.569 0.400,0.178 10 ATX- 0.974,0.674 1.749,1.567 false 1.746,1.987 2.198,2.446 false 0.325,3.036 0.705,3.201 0.380,0.165 10 TXM- 2.648,4.125 3.071,4.287 0.423,0.162 10 TXM+ 0.775,3.111 1.551,3.888 false 1.81,3.967 2.582,4.201 false

Disconnect the F1 and F55 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-5 (ATX+) - F1-15 (ATX-) Always 60 to 80 Ω
F55-9 (TXM+) - F55-10 (TXM-) Always 60 to 80 Ω


Text in Illustration
*1 Component without harness connected
(Radio Receiver Assembly)
*2 Component without harness connected
(Radio Receiver Assembly)



OK

3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE

NG

3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
a.

Enter diagnostic mode.

E110915E19
1.135,0.792 1.344,0.979 0.208,0.188 10 false *1 1.135,1.333 1.354,1.521 0.219,0.188 10 false *1 1.125,1.854 1.333,2.042 0.208,0.188 10 false *1 1.125,2.323 1.333,2.51 0.208,0.188 10 false *1 1.125,3.24 1.323,3.427 0.198,0.188 10 false *1 0.448,0.667 0.802,0.854 0.354,0.188 10 false *1 4.177,2.573 4.396,2.76 0.219,0.188 10 false *1 4.177,3.063 4.396,3.25 0.219,0.188 10 false *1 4.177,3.615 4.396,3.802 0.219,0.188 10 false *1 4.167,4.135 4.385,4.323 0.219,0.188 10 false *1 4.167,5 4.385,5.188 0.219,0.188 10 false *1 4.146,5.896 4.385,6.083 0.24,0.188 10 false *1 3.177,4.031 3.396,4.219 0.219,0.188 10 false *1 4.823,5.896 5.031,6.083 0.208,0.188 10 false *2 4.823,4.99 5.177,5.177 0.354,0.188 10 false *2 4.802,4.125 5.135,4.313 0.333,0.188 10 false *2 4.792,3.604 5.146,3.792 0.354,0.188 10 false *2 4.802,3.052 5.135,3.24 0.333,0.188 10 false *2 4.802,2.563 5.135,2.75 0.333,0.188 10 false *2 6.26,2.448 6.594,2.635 0.333,0.188 10 false *2 1.771,3.24 2.146,3.427 0.375,0.188 10 false *2 1.771,2.302 2.073,2.49 0.302,0.188 10 false *2 1.76,1.854 2.104,2.042 0.344,0.188 10 false *2 1.771,1.323 2.104,1.51 0.333,0.188 10 false *2 1.771,0.781 2.073,0.969 0.302,0.188 10 false *2 2.427,0.646 2.646,0.833 0.219,0.188 10 false *2 3.302,1.896 3.646,2.083 0.344,0.188 10 false *3 2.865,2.292 3.208,2.479 0.344,0.188 10 false *4 0.417,4.979 2.104,5.156 1.688,0.177 10 false *1: SEEK TRACK DOWN 0.427,5.26 1.948,5.438 1.521,0.177 10 false *2: SEEK TRACK UP 0.417,5.531 2.052,5.698 1.635,0.167 10 false *3: PRESET SWITCH "2" 0.427,5.792 2.063,5.958 1.635,0.167 10 false *4: PRESET SWITCH "3" 5.74,3.615 6.063,3.781 0.323,0.167 10 false DTC 3.406,1.26 5.854,1.469 2.448,0.208 10 false Component which has stored this code 2.021,0.198 3.5,0.375 1.479,0.177 10 false Service Check Mode 4.938,0.792 6.729,0.969 1.792,0.177 10 false Detailed Information Mode 3.677,4.469 6.385,4.802 2.708,0.333 10 false Continues to display detailed information of the first code. 3.594,5.302 6.594,5.656 3,0.354 10 false Continues to display detailed information when more DTCs are stored. 0.406,2.688 2.708,3.01 2.302,0.323 10 false Continues to display check result when more components are installed. 0.063,0.021 0.771,0.198 0.708,0.177 10 false Example


b.

Press preset switch "2" to change the mode to "Detailed Information Mode".


c.

Identify the component which has stored this code.

Component Table
Component Physical Address
Stereo component amplifier assembly 440
Radio receiver assembly 190
Multi-media interface ECU 388

HINT:
·

"P440" set by the stereo component amplifier assembly is shown in the preceding illustration as an example.

·




NEXT

4.CHECK COMPONENT SHOWN BY SUB-CODE
4.CHECK COMPONENT SHOWN BY SUB-CODE
a.

Select the component shown by the sub-code.

Component Table
Component Proceed to
Except radio receiver assembly A
Radio receiver assembly (190) B



A

5.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
HINT:

For details of the connectors, refer to Terminals of ECU (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(w/o Navigation System)>TERMINALS OF ECU).


a.

Referring to the following AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver assembly and component which has stored this code.

i.

Disconnect all connectors between the radio receiver assembly and component which has stored this code.


ii.

Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and component which has stored this code.

OK:

There is no open or short circuit.


E194159E12
5.229,3.938 6.552,4.365 1.323,0.427 10 false Multi-media Interface ECU*2 0.948,4.115 1.958,4.51 1.01,0.396 10 false Radio Receiver Assembly*1 2.427,1.25 2.823,1.469 0.396,0.219 10 false F1 2.427,1.74 2.823,1.958 0.396,0.219 10 false F1 1.927,1.167 2.323,1.385 0.396,0.219 10 false ATX+ 1.927,1.635 2.323,1.854 0.396,0.219 10 false ATX- 2.458,1.021 2.708,1.208 0.25,0.188 10 false 5 2.427,1.521 2.719,1.708 0.292,0.188 10 false 15 5.25,1.25 5.646,1.469 0.396,0.219 10 false TX+ 5.25,1.708 5.646,1.927 0.396,0.219 10 false TX- 4.917,1.24 5.177,1.417 0.26,0.177 10 false F18 4.917,1.729 5.188,1.896 0.271,0.167 10 false F18 4.917,3.021 5.188,3.198 0.271,0.177 10 false L40 4.917,3.51 5.188,3.667 0.271,0.156 10 false L40 5.25,3.021 5.646,3.24 0.396,0.219 10 false TX1- 5.26,3.479 5.656,3.698 0.396,0.219 10 false TX1+ 2.396,3.031 2.656,3.219 0.26,0.188 10 false F55 2.396,3.51 2.656,3.677 0.26,0.167 10 false F55 4.948,2.802 5.146,3.021 0.198,0.219 10 false 10 4.99,3.25 5.188,3.469 0.198,0.219 10 false 9 4.99,1.031 5.229,1.229 0.24,0.198 10 false 8 4.99,1.521 5.208,1.698 0.219,0.177 10 false 7 2.469,3.323 2.677,3.5 0.208,0.177 10 false 9 2.406,2.813 2.646,2.99 0.24,0.177 10 false 10 1.906,3.5 2.313,3.698 0.406,0.198 10 false TXM+ 1.906,3.021 2.271,3.24 0.365,0.219 10 false TXM- 0.292,4.906 1.563,5.146 1.271,0.24 10 false *1: Master Unit 0.292,5.229 1.563,5.469 1.271,0.24 10 false *2: Slave Unit 0.167,0.031 2.323,0.229 2.156,0.198 10 false AVC-LAN WIRING DIAGRAM: 5.208,2.156 6.625,2.49 1.417,0.333 10 false Stereo Component Amplifier Assembly*2




OK

6.REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE RADIO RECEIVER ASSEMBLY
a.

Replace the radio receiver assembly with a known good one.



NEXT

7.CLEAR DTC
8.RECHECK FOR DTC
a.

Recheck for DTCs and check if the same problem occurs again.

OK:

Malfunction disappears.




OK

END

NG

REPLACE COMPONENT WHICH HAS STORED THIS CODE