Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being to driven and makes it impossible to connect or register a "Bluetooth" device while driving.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E194845E11
5.167,1.885 5.49,2.104 0.323,0.219 10 false +S 4.854,1.75 5.083,1.969 0.229,0.219 10 false 4 4.844,3.167 5.073,3.385 0.229,0.219 10 false 3 2.823,1.74 3.052,1.958 0.229,0.219 10 false 11 3.781,1.76 4.01,1.979 0.229,0.219 10 false 61 5.146,0.792 5.469,1.01 0.323,0.219 10 false SI 4.823,0.667 5.052,0.885 0.229,0.219 10 false 3 1.458,0.802 1.781,1.021 0.323,0.219 10 false SP1 5.135,3.302 5.458,3.521 0.323,0.219 10 false SPD 1.896,0.646 2.125,0.865 0.229,0.219 10 false 12 0.521,1.396 1.917,1.698 1.396,0.302 10 false Skid Control ECU 4.729,2.51 6.719,2.75 1.99,0.24 10 false Combination Meter Assembly 5.104,3.958 6.135,4.26 1.031,0.302 10 false Radio Receiver 2.833,3.885 4.115,4.146 1.281,0.26 10 false Junction Connector 2.823,2.458 4.344,2.771 1.521,0.313 10 false Junction Connector 3.823,3.177 4.052,3.396 0.229,0.219 10 false 3 2.865,3.177 3.094,3.396 0.229,0.219 10 false 1 2.833,3.719 3.177,3.948 0.344,0.229 10 false F22 5.104,3.781 5.417,4.021 0.313,0.24 10 false F19 4.76,2.323 5.094,2.563 0.333,0.24 10 false E7 2.823,2.292 3.188,2.5 0.365,0.208 10 false E58 0.521,1.219 0.927,1.448 0.406,0.229 10 false A24

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U166128E01
0.276,1.135 0.615,1.310 0.339,0.174 10 E7 2.674,0.59 2.106,1.247 false 2.705,0.499 2.945,0.672 0.240,0.173 10 +S 0.78,3.803 0.78,4.176 false 1.467,3.807 1.467,4.176 false 0.866,4.086 1.39,4.086 false 1.003,4.133 1.298,4.296 0.295,0.163 10 (A) 2.86,3.717 3.234,3.880 0.375,0.163 10 GND 0.154,0.092 0.397,0.283 0.243,0.191 10 *1

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal E7-4 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal E7-4 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform is displayed as shown in the illustration.


Text in Illustration
*1 Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F19 radio receiver assembly and E7 combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-3 (SPD) - E7-4 (+S) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR