Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  CB-13  USB Over Current Detection  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
CB-13 USB device or "iPod" overcurrent malfunction
·

USB device or "iPod"

·

No. 1 stereo jack adapter assembly

·

Wire harness or connector

·

Multi-media interface ECU



WIRING DIAGRAM

E249768E03
1.594,1.323 2.135,1.469 0.542,0.146 10 false UPO 2.01,1.208 2.219,1.365 0.208,0.156 10 false 1 5.281,1.313 5.823,1.458 0.542,0.146 10 false UPO 5.115,1.177 5.323,1.333 0.208,0.156 10 false 1 1.49,0.719 2.031,0.865 0.542,0.146 10 false UESG 2.01,0.646 2.219,0.802 0.208,0.156 10 false 4 5.281,0.688 5.823,0.833 0.542,0.146 10 false UJSG 1.052,2.042 2.083,2.375 1.031,0.333 10 false Multi-media Interface ECU 5.021,2.01 6.219,2.406 1.198,0.396 10 false No. 1 Stereo Jack Adapter Assembly 1.042,1.823 1.417,2.01 0.375,0.188 10 false L55 5.021,1.813 5.396,2 0.375,0.188 10 false m1 5.115,0.615 5.323,0.771 0.208,0.156 10 false 4

PROCEDURE

1.REPLACE USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Turn the engine switch off.

HINT:

When one of these DTCs has been stored, it is necessary to turn off the engine switch to make it possible for the vehicle to recognize a new device when it is connected.



c.

Turn the engine switch on (ACC).


d.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.



NEXT

2.CLEAR DTC
3.RECHECK FOR DTC
a.

Recheck for DTCs and check if the same DTC occurs again.

HINT:

If DTCs are detected frequently, replace the multi-media interface ECU.


OK:

Malfunction disappears.




OK

USB DEVICE OR "iPod" WAS DEFECTIVE

NG

4.INSPECT MULTI-MEDIA INTERFACE ECU
4.INSPECT MULTI-MEDIA INTERFACE ECU
a.
U166126E01
0.122,0.086 0.337,0.266 0.215,0.180 10 *1 0.494,1.957 0.708,2.115 0.213,0.158 10 m1 0.458,0.904 0.821,1.063 0.363,0.159 10 UPO 0.886,0.982 1.332,1.918 false 2.66,0.646 3.087,0.816 0.427,0.170 10 UJSG 1.974,1.917 2.611,0.75 false

Disconnect the m1 No. 1 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m1-1 (UPO) - m1-4 (UJSG) Always 5 V


Text in Illustration
*1 Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NO. 1 STEREO JACK ADAPTER)
5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NO. 1 STEREO JACK ADAPTER)
a.

Disconnect the L55 multi-media interface ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L55-1 (UPO) - m1-1 (UPO) Always Below 1 Ω
L55-4 (UESG) - m1-4 (UJSG) Always Below 1 Ω
m1-1 (UPO) - Body ground Always 10 kΩ or higher
m1-4 (UJSG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR