Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(w/o Navigation System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255479 AUDIO AND VISUAL SYSTEM(w/o Navigation System) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/o Navigation System)  Mute Signal Circuit between Radio Receiver and Multi-media Interface ECU  


DESCRIPTION

The multi-media interface ECU sends a mute signal to the radio receiver assembly.

The radio receiver assembly controls the volume according to the mute signal from the multi-media interface ECU.

The mute signal is sent to reduce noise and popping sounds generated when switching modes.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the radio receiver assembly is functioning, no sound, or only an extremely faint sound, can be heard.

WIRING DIAGRAM

E175068E20
0.115,2.137 0.424,2.306 0.309,0.170 10 L40 0.103,2.314 1.877,2.497 1.774,0.184 10 Multi-media Interface ECU 5.499,2.344 7.127,2.536 1.628,0.191 10 Radio Receiver Assembly 1.02,1.111 1.467,1.297 0.448,0.185 10 MUTI 5.748,1.128 6.203,1.321 0.455,0.193 10 MUTE 5.49,2.181 5.791,2.351 0.302,0.170 10 F55 5.467,0.993 5.634,1.160 0.166,0.166 10 6 1.55,0.985 1.768,1.151 0.218,0.166 10 6

PROCEDURE

1.INSPECT RADIO RECEIVER ASSEMBLY
a.
U165830E01
0.205,0.124 0.458,0.280 0.253,0.156 10 *1 0.342,2.169 0.804,2.370 0.461,0.201 10 MUTE 1.253,2.186 0.875,2.244 false 1.56,1.267 1.883,1.437 0.323,0.170 10 F55

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F55-6 (MUTE) - Body ground Engine switch on (ACC), USB audio system is playing → Mode is changing Above 2.5 V → Below 0.5 V


Text in Illustration
*1 Component with harness connected
(Radio Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-MEDIA INTERFACE ECU)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-MEDIA INTERFACE ECU)
a.

Disconnect the F55 radio receiver assembly and L40 multi-media interface ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-6 (MUTE) - L40-6 (MUTI) Always Below 1 Ω
F55-6 (MUTE) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MULTI-MEDIA INTERFACE ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MULTI-MEDIA INTERFACE ECU
a.
U165831E02
1.25,2.198 0.875,2.24 false 0.271,0.177 0.563,0.385 0.292,0.208 10 false *1 0.365,2.167 0.823,2.365 0.458,0.198 10 false MUTI 1.573,1.333 1.896,1.5 0.323,0.167 10 false L40

Reconnect the L40 multi-media interface ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L40-6 (MUTI) - Body ground Engine switch on (ACC) Above 2.5 V


Text in Illustration
*1 Component with harness connected
(Multi-media Interface ECU)



OK

NG