Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2015.08–2017.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

U166445E02
2.615,1.083 4.396,1.5 1.781,0.417 10 false Park/Neutral Position Switch Assembly*1 5.302,1.229 5.729,1.417 0.427,0.188 10 false F124 5.313,1.406 6.646,1.75 1.333,0.344 10 false Radio and Display Receiver Assembly 2.615,0.875 2.938,1.063 0.323,0.188 10 false C24 0.521,0.552 1.5,0.906 0.979,0.354 10 false from BKUP LP Fuse 3.729,0.427 3.99,0.615 0.26,0.188 10 false RL 3.083,0.427 3.344,0.615 0.26,0.188 10 false RB 5.417,0.583 5.75,0.771 0.333,0.188 10 false REV 5.229,0.438 5.365,0.625 0.135,0.188 10 false 2 4.448,0.438 4.625,0.625 0.177,0.188 10 false *1 4.708,0.813 4.917,1 0.208,0.188 10 false *2 2.896,0.438 3.031,0.625 0.135,0.188 10 false 2 2.573,2.49 3.646,2.677 1.073,0.188 10 false C39 4.01,0.438 4.135,0.625 0.125,0.188 10 false 1 4.01,2 4.156,2.188 0.146,0.188 10 false 1 2.896,2 3.042,2.188 0.146,0.188 10 false 2 2.573,2.667 4.719,2.854 2.146,0.188 10 false Back-up Light Switch Assembly*2 0.083,3.385 2.063,3.573 1.979,0.188 10 false *2: for Manual Transmission 0.083,3.115 2.063,3.302 1.979,0.188 10 false *1: for Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK)]


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK
Shift Lever Position Display
R ON
Except R OFF

HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
U166601E01
0.09,0.084 0.382,0.296 0.291,0.212 10 *a 0.104,0.63 0.525,0.842 0.421,0.212 10 REV 0.936,1.369 0.717,0.7 0.717,0.7 0.5,0.7 false 1.517,0.448 1.885,0.660 0.368,0.212 10 F124

a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F124-2 (REV) - Body ground Engine switch on (IG), shift lever in R 7.5 to 14 V
F124-2 (REV) - Body ground Engine switch on (IG), shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the F124 radio and display receiver assembly connector.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-2 (REV) - C24-1 (RL) Always Below 1 Ω
F124-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U166427E02
1.792,1.031 2.01,0.365 2.01,0.365 2.229,0.365 false 2.281,0.281 2.573,0.49 0.292,0.208 10 false RB 0.281,1.01 0.573,1.219 0.292,0.208 10 false C24 0.125,0.083 0.417,0.292 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AB60F) A
OK (for A750F) B
OK (for AE80F) C
NG D



A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F124 radio and display receiver assembly connector.


b.

Disconnect the C39 back-up light switch assembly connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-2 (REV) - C39-1 Always Below 1 Ω
F124-2 (REV) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
U166425E02
0.156,0.094 0.365,0.292 0.208,0.198 10 false *a 0.479,1.323 0.781,1.521 0.302,0.198 10 false C39

Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C39-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR