Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  B15D6  Display Disconnected  


DESCRIPTION

The multi-display assembly and multi-media module receiver assembly are connected by an AVC-LAN communication line.

When an AVC-LAN communication error occurs between the display module board and multi-display assembly, this DTC is will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D6 A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Harness or connector

·

AVC-LAN circuit

·

Multi-display assembly

·

Multi-media module receiver assembly



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The multi-media module receiver assembly is the master unit.



WIRING DIAGRAM

E263454E16
5.521,0.542 5.917,0.698 0.396,0.156 10 false TX3+ 5.531,0.948 6.042,1.135 0.51,0.188 10 false TX3- 3.635,0.958 3.948,1.156 0.313,0.198 10 false TX- 3.635,0.51 3.948,0.708 0.313,0.198 10 false TX+ 2.99,0.542 3.302,0.74 0.313,0.198 10 false B 2.979,0.958 3.292,1.156 0.313,0.198 10 false ACC 1.885,0.688 2.427,0.938 0.542,0.25 10 false RADIO 1.813,1.094 2.604,1.344 0.792,0.25 10 false ECU-ACC 0.531,0.521 1.406,0.771 0.875,0.25 10 false from Battery 0.302,0.927 1.385,1.135 1.083,0.208 10 false from ACC Relay 0.708,2.417 2.708,2.646 2,0.229 10 false : AVC-LAN Communication Line 2.865,1.667 3.177,1.865 0.313,0.198 10 false F79 2.844,1.813 4.208,2.156 1.365,0.344 10 false Multi-display Assembly 5.417,1.656 5.823,1.917 0.406,0.26 10 false F77 5.406,1.813 6.75,2.25 1.344,0.438 10 false Multi-media Module Receiver Assembly 5.323,0.844 5.729,1.104 0.406,0.26 10 false 46 5.323,0.438 5.729,0.698 0.406,0.26 10 false 45 3.938,0.448 4.344,0.708 0.406,0.26 10 false 7 3.927,0.833 4.333,1.094 0.406,0.26 10 false 19 2.969,1.354 3.396,1.563 0.427,0.208 10 false GND1 2.75,0.427 3.063,0.625 0.313,0.198 10 false 12 2.76,0.823 3.073,1.021 0.313,0.198 10 false 24 2.76,1.219 3.073,1.417 0.313,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

2.CHECK FOR DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166144E02
2.5,1.51 2.688,1.781 false 0.896,1.51 0.688,1.771 false 2.469,1.26 2.792,0.823 false 0.104,0.042 0.271,0.208 0.167,0.167 10 false *a 1.552,0.448 1.833,0.615 0.281,0.167 10 false F79 2.833,0.667 3.104,0.833 0.271,0.167 10 false B 2.594,1.833 2.927,2.031 0.333,0.198 10 false ACC 0.313,1.813 0.76,1.99 0.448,0.177 10 false GND1

Disconnect the multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-12 (B) - F79-13 (GND1) Always 11 to 14 V
F79-24 (ACC) - F79-13 (GND1) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-display Assembly)


OK

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E57
2.698,1.781 2.521,1.781 2.521,1.781 2.385,1.344 true 1.958,1.771 2.115,1.771 2.115,1.771 2.26,1.333 true 1.656,1.698 1.99,1.917 0.333,0.219 10 false TX3- 2.781,1.708 3.198,1.906 0.417,0.198 10 false TX3+

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F79 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-45 (TX3+) - F79-7 (TX+) Always Below 1 Ω
F77-46 (TX3-) - F79-19 (TX-) Always Below 1 Ω
F77-45 (TX3+) or F79-7 (TX+) - Body ground Always 10 kΩ or higher
F77-46 (TX3-) or F79-19 (TX-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).



NEXT

7.CLEAR DTC
8.CHECK FOR DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY